Geely Emgrand X7. Manual part — 478
Geely Emgrand X7. Manual part - 478
10.2.4.7 DTC B1209 B1210
Fault diagnosis code Descriptions
B1209
Right front/right rear steering lamp,One of both has open circuit fault
B1210
The right front and right rear steering lamps are shorted to ground.
Circuit diagram:
NL11-3210b
6 SO31
3 SO31
8 CA12
8 IP48
9 IP48
5 CA12
8 CA18
5 CA18
6 SO24
3 SO24
左后组合灯
(左转向灯)
左前组合大灯
(左转向灯)
右前组合大灯
(右转向灯)
右后组合灯
(右转向灯)
BCM
TURN-LH LAMP
TURN-RH LAMP
Diagnostic Steps:
1
Check any fault code except forB1209 B1210
(a) Check if any fault code exists except for B1209 B1210
2
Measure right steering lamp voltage.
Yes
Go to
DTC list in 10.2.4.2
and repair according to
trouble codes.
No
Left rear
combinati
on lamp
(left
steering
lamp)
Left front
combination
headlamp (left
steering lamp)
Right front
combinatio
n headlamp
(right
steering
lamp)
Right
rearcombinatio
n lamp (right
steering lamp)
1911
(a) Turn the ignition switch to ON position.
(b) Turn on right turning lamp.
(c) Measure right front steering lamp harness
connector CA18 terminal8, right rear steering
lamp harness connector SO24 terminal6.
Standard Voltage: 11-14 V
NL11-3214b
9
8
7
4
3
2
6
5
1
1
2
6
3
4
5
CA18右前组合灯线束连接器
SO24右后组合灯线束连接器
3
Inspect the bulb.
(a) Check if the bulb of turning light is blown.
Is the bulb filament blown?
4
Inspect the communication among the BCM, the right front
steering lamp and the right rear steering lamp.
No
Go to step 4
Yes
Yes
Replace the bulb.
No
CA18 right front combination lamp harness connector
SO24 right rearcombination lamp harness connector
1912
(a) Turn the ignition switch to OFF
position.
(b) Disconnect BCM harness connector
IP48.
(c) Disconnect the steering lamp harness
connectorCA18、SO24.
(d) Measure resistance between BCM
wire harness connector IP48 terminal 9
and license lamp wire harness
connector CA12 terminal 8.
(e) Measure resistance between BCM
wire harness connector IP48 terminal 9
and license lamp wire harness
connector SO24 terminal 6.
Standard Resistance: Less than 1 Ω
Confirm if the resistance conforms to
standard value.
NL11-3215b
9
8
7
4
3
2
6
5
1
1
2
6
3
4
5
CA18右前组合灯线束连接器
IP48BCM线束连接器
SO24右后组合灯线束连接器
1 2 3
4 5 6
7 8 9
10 11 12 13
5
Inspect the communication among the right front steering lamp, the
right rear steering lamp and grounding.
No
Repair or replace the harness.
Yes
IP48BCMharness connector
CA18 right front combination lamp harness connector
SO24 right rearcombination lamp harness connector
1913
(a) Disconnect steering lamp harness
connector CA18, SO24.
(d) Measure the resistance between
terminal 5 of license lamp harness
connector CA18 and grounding.
(c)
Measure resistance between
license lamp wire harness
connector SO24 terminal 3 and
grounding.
Standard Resistance: Less than 1 Ω
(d) Measure the resistance between
terminal 8 of license lamp harness
connector CA18 and grounding.
(e)
Measure resistance between
license lamp wire harness
connector SO24 terminal 6 and
grounding.
Standard Resistance: More than 10 Ω
or higher
Confirm if the resistance conforms to
standard value.
NL11-3216b
9
8
7
4
3
2
6
5
1
1
2
6
3
4
5
CA18右前组合灯线束连接器
SO24右后组合灯线束连接器
6
Replace the BCM
(a) Replace BCM and refer to
Replacement of BCM in 11.8.8.1
.
Confirm the completion of repair.
7
The system is normal.
No
Repair or replace the harness.
Yes
Next
CA18 right front combination lamp harness connector
SO24 right rearcombination lamp harness connector
1914
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст