Geely Emgrand X7. Manual part — 112

2.6.8.2 Replacement of Cylinder Hood Cover

Warning: refer to "warning of battery disconnection" in "warnings and precautions".

Dismantlement Procedure

1. Disconnect the battery negative

electrode cable. Refer to 2.12.6.1
Battery Disconnection.

2. Refer to 2.6.8.1 "Replacement of

Plastic Shield of Engine" to
dismantle the engine shied.

3. Dismantle ignition coil and

ignition guide wire, refer to“2 .
10.7.3ignition coil
replacement ” .

4. Dismantle forced venting pipe of

crankshaft

5. Dismantle the crankcase

ventilation tube .

GC02-0010c

6. Dismantle cylinder hood cover

bolts and nuts.

GC02-0011c

7. Remove the cylinder hood cover.

GC02-0012c

447

8. Dismantle the cylinder hood cover

seal gasket from the cylinder
hood cover.

GC02-0011c

Installation Procedure:

1. Install the cylinder hood cover

gasket.

2. Apply sealant evenly in the

cylinder hood gasket.

3. Install the cylinder hood cover.

4. Tighten the cylinder hood cover

bolts.

Note: When tightening, tighten a
single bolt several times, in
accordance with the specified torque.

Short Bolts:

Torque: 10-12 N.m (Metric)

Long Bolts, Nuts, Special Bolts:

Torque: 10-12 N.m (Metric)

GC02-0013c

5. Install the forced ventilation

rubber hose of the crankcase.

6. Install the crankcase ventilation

vacuum tube.

7. Install the ignition coil and

ignition wire.

8. Install the plastic shield of

engine.

9. Connect battery negative cable.

GC02-0010c

448

2.6.8.3 Replacement of Drive Belt

Dismantlement Procedure

Warning: Refer to "Warning on
Battery Disconnection" in "Warning
and Precautions".

1. Disconnect the battery negative

electrode cable. Refer to 2.12.6.1
Battery Disconnection.

Rotate the drive belt tensioner
anti-clockwise with a wrench to
remove the drive belt.

Note: In the removal process, prevent
the wrench slipping causing injury to
the operator.

GC02-0015c

Installation Procedure:

1. Wrap the drive belt as shown.

2. Rotate the drive belt tensioner

clockwise with a wrench to
install the drive belt.

3. Release drive belt tensioner to

normal position.

Important precaution : Before
releasing the tensioner device,
confirm the drive belt aligned with
drive pulley groove, otherwise the
drive belt may be damaged.

4. Connect battery negative cable.

GC02-0014c

449

2.6.8.4 Replacement of Drive Belt Tensioner

Dismantlement Procedure

1. Disconnect the battery negative

electrode cable. Refer to 2.12.6.1
Battery Disconnection.

2. Refer to 2.6.8.1 "Replacement of

Plastic Shield of Engine" to
dismantle the engine shied.

3. Refer to 2.6.8.3 "Replacement of

Drive Belt" to dismantle the drive
belt.

4. Dismantle the fixing bolts at the

end of drive belt tensioner
hydraulic unit.

FE02-3019b

5. Dismantle the fixing bolts of

drive belt tensioner pulley
bracket.

FE02-3020b

Installation Procedure:

1. Install drive belt tensioner

support fixing bolt.

Torque :60N. m(Metric) 44 .
28lb-ft(English system)

2. Install hydraulic unit end of drive

belt tensioner Fixing Bolts

Torque: 32 Nm (Metric) 23.62 lb-ft
(English system)

3. Install the drive belt.

4. Install the engine hood.

5. Connect battery negative cable.

FE02-3020b

450