Geely Emgrand X7. Manual part — 113
Geely Emgrand X7. Manual part - 113
2.6.8.5 Replacement of Electrical Throttle Body Assembly
Dismantlement Procedure
Warning: Refer to "Warning on
Battery Disconnection" in "Warning
and Precautions".
1. Disconnect the battery negative
cable. Refer to 2.12.6.1 Battery
Cable Disconnection/Connection
Procedure.
2. Disconnect the electronic throttle
wiring harness connection.
3. Dismantle intake main pipe from
the throttle body.
GC02-0017c
4. Dismantle the fixing bolts and
nuts of throttle body from the
intake main pipe.
5. Dismantle electronic throttle
body.
GC02-0016c
Installation Procedure:
1. Clean the engine throttle body
and the engine intake manifold
mating surface and replace the
seals.
2. Install the electronic throttle
body to the intake main pipe and
tighten the fixing bolts and nuts.
3. Connect the idle speed control
valve harness connector.
4. Install and tighten the intake
main pipe clamp.
5. Connect battery negative cable.
GC02-0016c
451
2.6.8.6 Replacement of Intake Manifold Assembly
Dismantlement Procedure
1. Disconnect the battery negative
electrode cable. Refer to 2.12.6.1
Battery Disconnection.
2. Refer to 2.6.8.1 "Replacement of
Plastic Shield of Engine" to
dismantle the engine shied.
3. Refer to 2.6.8.5. "Replacement of
Throttle Body Assembly" to
dismantle the throttle body.
4. Dismantle the PCV hose.
5. Dismantle the canister solenoid
valve vacuum tube.
6. Dismantle the vacuum booster
vacuum hose.
GC02-0018c
7. Dismantle the fixing bolts and
nuts of intake manifold in the
sequence as shown in the figure.
5
3
4
2
1
GC02-0019c
Installation Procedure:
1. Clean the cylinder head intake
manifold installation surface.
2. Clean the intake manifold
installation surface.
3. Install the intake manifold seals.
GC02-0020c
452
4. Tighten the intake manifold
retaining bolts and nuts in the
sequence shown in the graph.
Note: The bolts and nuts can not
tighten to the specified torque at
once, otherwise it will result in the
intake manifold leakage. They should
be tightened at several stages to the
specified torques.
Torque: 30N.m (Metric system)
22.3lb-ft (English system)
1
3
2
4
5
GC02-0021c
5. Install the vacuum booster
vacuum hose.
6. Install the canister solenoid valve
vacuum tube.
7. Install the forced ventilation
vacuum pipe of the crankcase.
8. Install the throttle body.
9. Install the mounting bracket of
intake manifold and tighten the
fixing bolts.
10. Install the engine hood.
11. Install negative cable of battery.
GC02-0018c
453
2.6.8.7 Engine supporting seat Replacement
Dismantlement Procedure
Warning: Refer to "Warning on Battery Disconnection" in "Warning and Precautions".
1. Disconnect the battery negative
electrode cable. Refer to 2.12.6.1
Battery Disconnection.
2. Dismantle the plastic shield of
engine. Refer to 2.6.8.1
Replacement of Plastic Shield of
Engine.
3. Support the engine assembly
with a jack.
Note: prior to support, a wood block
is placed between the jack and the
engine sump; otherwise, the engine
sump will be damaged!
FE02-0126b
4. Dismantle the body to engine
right suspension bolts.
5. Dismantle the engine to engine
right suspension bolts.
GC02-0023c
6. Dismantle the fixing bolts of
engine mount and dismantle the
engine mount.
GC02-0022c
454
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст