Geely Emgrand X7. Manual part — 198
Geely Emgrand X7. Manual part - 198
2.12.7.28 DTC P0230
1. DTC
description:
DTC P0230
Fuel Pump Relay Fault
The power pump relay coil working voltage is provided by ECM. ECM provides power through
ECM harness connector EN01 terminal No.71 to pump relay terminal No.1. The fuel pump is
grounded through the terminal No.2, fuel pump relay pull-in. ECM has an internal detection
circuit. By monitoring the feedback voltage ECM determines whether the control circuit is open,
short to ground or short to voltage.
2. Conditions For Setting DTC and The Fault Location:
DTC Code
DTC Detection
Strategy
Conditions For Setting The DTC
(Control Strategy)
Fault Locations
P0230
Hardware
Circuit
Inspection
Fuel Pump Relay Control Circuit Short to
Power Supply or Ground or Open
1. Relay
Circuit
2. Relay
3. ECM.
3. Circuit
sketch
NL02-2074b
3 SO26
9 EN01
44 EN01
68 EN01
4 SO26
M
ECM
IG2
BAT
10A
IF
3
3
15
A
E
F2
5
15
A
E
F2
1
FPR
MPR
IGN
1
3
2
5
86
87
30
85
燃油泵
燃油泵继电器
发动机主继电器
67 EN01
BAT
10
A
E
F1
6
BAT
4. Diagnostic
Steps:
Refer to 2.3.2 “Description and Operation” and 2.3.3 “ Operating Principle” to inspect the fuel
pump relay circuit.
Engine main
relay
Fuel pump
relay
Fuel
pump
791
2.12.7.29 DTC P0261 P0262
1. DTC
description:
DTC P0261
Cylinder No.1 Fuel Injector Circuit Low Voltage Fault
DTC P0262
Cylinder No.1 Fuel Injector Circuit High Voltage Fault
Fuel injectors operating voltage is provided by The Main Relay controlled by ECM. Battery
voltage passes through the main relay terminal No.3 to all fuel injector wiring harness connectors
terminal No.1. ECM controls Cylinder No.1 fuel injector internal ground circuit through ECM
harness connector EN01 terminal No.6. ECM monitors all fuel injector driver circuits status, if
ECM detects driving circuit status corresponding voltage is incorrect, ECM will set a fuel injector
control circuit fault DTC code.
2. Conditions For Setting DTC and The Fault Location:
DTC Code
DTC Detection
Strategy
Conditions For Setting The DTC
(Control Strategy)
Fault Locations
P0261
Hardware
Circuit
Inspection
Injector Signal Circuit Open or
Short To Ground
P0262
Hardware
Circuit
Inspection
Injector Signal Circuit Short To
Power Supply
1. Sensor
Circuit
2. Sensor
3. ECM.
3. Circuit
sketch
NL02-2075b
44
EN01
ECM
BAT
15
A
E
F2
1
MPR
86
87
30
85
发动机主继电器
6
EN01
A
EN11
B
EN11
INJA
1缸燃油喷射器
Engine main
relay
1st cylinderfuel injector
792
4. Diagnostic
Steps:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and
analyze the accuracy of the data, as these will help with quick diagnosis.
Step 1
Initial Inspection
(a) Inspect the fuel injector harness connector for damage, poor connection, aging or signs of
loosening
Step 2
Measure the fuel injector resistance.
(a) Disconnect the fuel injector harness connector EN11.
(b) Measure resistance between the two fuel injector terminals.
Standard Resistance
11.4-12.6Ωwith 20℃(68℉
(c) Connect the fuel injector harness connector EN11.
Step 3
Measure Fuel Injectors Working power supply
(a) Rotated ignition switch to OFF
position .
(b) Disconnect cylinder No.1 fuel
injector harness connector EN11.
(c) Rotated ignition switch to ON
position .
(d)
Measure voltage between
cylinder No.1 fuel injector
harness connector EN11 No.2
terminal and a reliable ground.
Standard Voltage: 11-14V
(e) Connect cylinder No.1 fuel
injector harness connector EN11.
NL02-2076b
A
B
EN11 1缸燃油喷射器线束连接器
A
No
Go to step 5
Yes
No
Refer to 2.2.8.2 “Replacement of Fuel Injectors” to
replace the fuel injectors
Yes
Next
EN11 1st cylinderfuel injector harness
connector
793
(a) Rotated ignition switch to OFF
position .
(b) Disconnect cylinder No.1 fuel
injector harness connector EN11.
(c) Connect test lamp made from
light-emitting diodes to the fuel
injector harness connector EN11
terminal No.1 and No.2.
(d) Start
the
engine.
NL02-2077b
A
B
EN11 1缸燃油喷射器线束连接器
A
B
(e) Observe whether test lamp is
flashing.
Is test lamp flashing as normal?
Step 5
Inspect and repair cylinder No.1 fuel injector power supply circuit.
NL02-2076b
A
B
EN11 1缸燃油喷射器线束连接器
A
4
Inspect the fuel injector control circuit.
Go to step 6
Go to step 7
No
Yes
EN11 1st cylinderfuel injector harness
connector
794
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст