Geely Emgrand X7. Manual part — 120
Geely Emgrand X7. Manual part - 120
9. Install the power steering gear tie
rod lateral pin bolts.
Refer to 3.3.6.1 “Inspect Gearbox Oil
and Liquid Level” to inspect the
tightness of the gearbox oil exhaust
bolts and refill the gearbox oil.
11. Lower the vehicle.
12. Install the front wheels.
NL02-0187b
13. Install the heater intake and
outlet pipes.
14. Install gear shift lever cable.
15. Install canister vacuum tubes.
16. Install the fuel pipe.
17. Install grounding point of battery
negative cable in gearbox
housing.
18. Connect the engine wiring
harness to the engine cabin
junction box connecting cables
and connectors.
NL02-0186b
19. Install fixing bolts of clutch slave
cylinder.
Torque :20Nm (Metric) 14 . 8lb-ft
(English system)
20. Install and tighten the fixing bolts
of clutch oil pipe bracket.
Torque:10Nm(Metric) 7.4lb-ft(English
system)
21. Install the vacuum booster
vacuum tubes.
22. Install the radiator inlet and
outlet pipes.
23. Install radiator water outlet pipe.
24. Install the intake main pipe
assembly.
NL02-0007c
479
25.
Install the air-conditioning
compressor high and low
pressure connecting pipes.
Torque :18Nm (Metric) 13 . 3lb-ft
(English system)
26. Connect the front and rear
oxygen sensor harness
connectors.
27. Connect the engine control unit
and engine harness to the
instrument panel harness
connectors.
28. Install grove box of instrument
desk .
29. Install battery and bottom plate.
30. Install the Coolant Recovery
Reservoir.
31. Fill engine coolant.
32.
Fill the air-conditioning
refrigerant .
33. Connect the battery negative
cable .
NL02-0174b
480
2.6.8.14 Replacement of Cylinder Hood Assembly
Dismantlement Procedure
1. Disconnect the battery negative electrode cable. Refer to 2.12.6.1 Battery Disconnection.
2. Dismantle the plastic shield of engine. Refer to 2.6.8.1 Replacement of Plastic Shield of
Engine.
3. Refer to 2.8.8.1 Engine Coolant Discharge and Filling to discharge the engine coolant.
4. Refer to "Replacement of Electrical Throttle Body Assembly" to dismantle the throttle body.
5. Refer to 2.6.8.6 "Replacement of Intake Manifold Assembly" to dismantle the intake
manifold assembly.
6. Refer to 2.7.6.1 "Replacement of Exhaust Manifold" to dismantle the exhaust manifold.
7. Dismantle ignition coil and ignition guide wire , refer to“2 . 10 . 7 . 3ignition coil
replacement ” .
8. Refer to 2.6.8.2 "Replacement of Cylinder Hood Cover" to dismantle the cylinder hood
cover.
9. Refer to 2.6.8.3 "Replacement of Drive Belt" to dismantle the drive belt.
10. Refer to 2.6.8.9 "Replacement of Timing Chain Cover" to dismantle the timing chain cover.
11. Refer to 2.6.8.10 "Replacement of Timing Chain" to dismantle the timing chain.
12. Refer to 2.3.8.5 “Replacement of Fuel Injector” to dismantle the fuel distributing pipe
assembly.
13. Refer to 2.2.8.2 "Replacement of
temperature sensor of engine
coolant" to disconnect the
temperature sensor of engine
coolant harness connector.
14. Refer to 2.10.7.1 "Replacement
of Camshaft Position Sensor" to
dismantle camshaft position
sensor.
15. Refer to 2.2.8.5 "Replacement of
VVT Solenoid Valve and Filter
Cleaning" to dismantle the VVT
Solenoid Valve.
16. Refer to 2.6.8.12 “Replacement
of Camshaft” to dismantle the
camshaft.
17. Dismantle the radiator inlet
pipes.
18. Dismantle the warm water pipe
for the heater tank.
GC02-0051c
481
19. Dismantle the cylinder hood
bolts according to the sequence
in the figure.
Note: When the engine is hot, it is
prohibited to dismantle the cylinder
hood, as this will cause the cylinder
hood distortion.
1
3
7
5
9
10
6
8
4
2
GC02-0052c
20. Remove the cylinder hood bolts.
Note: Due to confined space, cylinder
head bolts and bolt gaskets can not
be removed together.
GC02-0053c
21. Remove the cylinder hood bolt
gasket with a magnetic stick.
GC02-0054c
482
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст