Geely EC718, EC718RV, EC715, EC715RV. Manual part — 467
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 467
Symptoms
Suspected Parts
Measures / Refer to
6. If the above circuits are normal but the
symptoms still occur, replace the BCM
.
Set up the anti-theft system, the security
indicator does not blink
1. Alarm Indicator Circuit
Refer to
.
2. If the anti-theft indicator light circuit is
normal, replace the BCM
.
When the remote control has no power, in
the alarm mode with the ignition switch is
at ON position, the alarm sound can not be
canceled.
1. Ignition Switch Circuit
2. CAN-Bus Circuit
Refer
.
3. Replace the remote control battery. If
the remote control system is working
properly, replace the BCM
.
Even if the door is open, the alarm system
can still be set.
1. Door Controlled Lamp Switch Circuit
Refer to
.
2. If the door controlled lamp switch circuit
is normal, but the symptoms still occur,
replace the BCM
.
When the anti-theft alarm system is in
working condition, the vehicle anti-theft
horn is inoperative.
1. Horn Circuit
Refer to
.
2. If the horn circuit is normal, replace the
BCM
.
When the anti-theft alarm system is in
working condition, the hazard warning
lamps do not blink.
1. Hazard Warning Lamps Circuit
Operate the turn signal (hazard warning
lamps), if all the turning lights do not work,
check the turn signal circuit.
2. If all the turn signal lamps do not work,
replace the BCM
If all turn signal lamps do not work, replace
the BCM. Refer to
Body Electric
Remote Anti-theft System
11-381
11.10.7.5 Anti-theft Indicator Inoperative
Schematic:
Anti-theft Warning Lamp
Anti-theft Warning Horn
Body
Control
Module
FE11-5901b
Diagnostic Steps:
Note
Before carry out this diagnostic procedure, Select on the scan tool as the following sequence: Body Control / BCM
special set function / anti-theft indicator. Use scan tool to drive the anti-theft indicator, which helps with quick diagnostic.
Step 1
Check the fuse IF5.
IF14
IF2
IF1
IF5
IF7
IF3
IF16
IF27
IF25
IF26
IF28
IF30
IF24
IF20
IF19
IF23
IF18
IF21
IF13
IF12
IF15
IF9
IF10
IF8
F17
F22
M
FE11-5902b
(a)
Check whether the fuse IF5 is blown.
Fuse Rating: 10 A
11-382
Remote Anti-theft System
Body Electric
No
Yes
Step 2
Check the fuse IF5 circuit.
(a)
Check whether the fuse IF5 circuit is short.
(b)
Repair the circuits. Confirm that there are no short circuits.
(c)
Replace with fuses with rated current.
Is the anti-theft indicator working correctly?
Yes
System normal
No
Step 3
Measure the alarm indicator harness connector IP15 terminal No.1 voltage.
Anti-theft Warning Lamp Harness
Connector IP15
FE11-5903b
(a)
Measure IP15-1 voltage with a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
Yes
No
Step 4
Repair the open circuit between the anti-theft indicator wiring harness connector IP15 and the fuse IF5.
(a)
Confirm the open circuit between the anti-theft indicator
wiring harness connector IP15 and the fuse IF5 repair is
completed.
Is the anti-theft indicator working correctly?
Yes
System normal
No
Step 5
Check the alarm indicator.
Body Electric
Remote Anti-theft System
11-383
Anti-theft Warning Lamp Harness
Connector IP15
FE11-5904b
(a)
Disconnect the anti-theft indicator wiring harness connector.
Refer to
Anti-theft Indicator Lamp Replacement
.
(b)
Test continuity between the anti-theft light IP15 terminal No.
1 and 2 is consistent with a multimeter.
Yes
No
Step 6
Replace the anti-theft indicator.
(a)
Replace the anti-theft indicator. Refer to
Is the anti-theft indicator working correctly?
Yes
System normal
No
Step 7
Check the circuit between the BCM harness connector IP29 and the anti-theft indicator harness connector
IP15.
Anti-theft Warning Lamp Harness
Connector IP15
Body Control Module 1 Harness Connector IP29
FE11-5910b
(a)
Disconnect the anti-theft indicator wiring harness connector
IP15 and the BCM harness connector IP29.
(b)
Measure resistance between the BCM harness connector
IP29 terminal No.13 and the anti-theft indicator wiring
harness connector IP15 terminal No.2 with a multimeter.
Standard Resistance: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 8
Repair the open circuit between the BCM harness connector IP29 and the anti-theft indicator harness
connector IP15.
(a)
Confirm the open circuit between the BCM harness
connector IP29 and the anti-theft indicator harness connector
IP15 repair is completed.
Is the anti-theft indicator working correctly?
11-384
Remote Anti-theft System
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст