Geely EC718, EC718RV, EC715, EC715RV. Manual part — 432
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 432
Diagnostic Steps:
Note
Before carry out this diagnostic procedure, make sure that the rear wiper motor ground circuit is not faulty.
Step 1
Use scan tool active test function and check the rear wipers working status.
(a)
Select as the following sequence: body control module /
active test / rear wipers output control.
Are the rear wipers working properly?
Yes
No
Step 2
Measure the rear wiper motor wiring harness connector terminal No.2 voltage.
Rear Wiper Motor Harness Connector SO47
FE11-5522c
(a)
Disconnect the wiper motor wiring harness connector.
(b)
Turn on the ignition switch.
(c)
Activate the wiper switch, measure the wiper motor harness
connector terminal No.2 voltage with a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
Yes
Replace the wiper motor. Refer to
No
Step 3
Check the fuse IF28.
IF14
IF2
IF1
IF5
IF7
IF3
IF16
IF27
IF25
IF26
IF28
IF30
IF24
IF20
IF19
IF23
IF18
IF21
IF13
IF12
IF15
IF9
IF10
IF8
F17
F22
M
FE11-5529c
(a)
Check the fuse IF28.
Fuse Rating: 10 A
Is the fuse normal?
No
Check the circuits and replace the fuse,
confirm the fault has been fixed.
Body Electric
Wipers / Washers System
11-241
Yes
Step 4
Check the rear wiper relay control circuit.
46
45
44
43
42
41
40
39
38
37
36
35
34
33
25 26 27
18
17
16
2
1
4
3
7
6
5
28
29 30
31
24
22
21
20
23
19
9 10 11
8
13
12
15
14
32
I/P Fuse Block Harness Connector IP05
FE11-5530c
(a)
Find the wiring harness connector IP05 terminal No.2.
Note
Do not disconnect the wiring harness connector IP05.
(b)
Connect the wiring harness connector IP05 terminal No.2 to
the ground.
(c)
Turn the ignition switch to the ON position.
Confirm that wipers are working properly.
No
Yes
Step 5
Measure the wiper switch wiring harness connector terminal No.11 voltage.
Wiper Harness Connector IP19
FE11-5531c
(a)
Turn the ignition switch to the ON position.
(b)
Measure the wiper switch harness connector IP19 terminal
No.11 voltage with a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
No
Check the wiper switch power supply circuit
open.
Yes
Step 6
Check the wiper switch wiring harness connector terminal No.10 voltage.
11-242
Wipers / Washers System
Body Electric
Wiper Harness Connector IP19
FE11-5523c
(a)
Turn the ignition switch to the ON position.
(b)
Operate the rear wiper switch to normal position.
(c)
Measure the wiper switch harness connector IP19 terminal
No.10 voltage with a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
Yes
No
Step 7
Replace the wiper switch.
(a)
Replace the wiper switch. Refer to
Confirm that wipers are working correctly.
Yes
System normal
No
Step 8
Test continuity between the body control module (BCM) IP29 terminal No.14 and I/P fuse block wiring
harness connector IP05 terminal No.2.
1
2
3
4
5
6
7
8
9 10
20
30
40
19
29
39
18
28
38
17
27
37
16
26
36
15
25
35
14
24
34
13
23
33
12
22
32
11
21
31
46
45
44
43
42
41
40
39
38
37
36
35
34
33
25 26 27
18
17
16
2
1
4
3
7
6
5
28
29 30
31
24
22
21
20
23
19
9 10 11
8
13
12
15
14
32
I/P Fuse Block Harness Connector IP05
Body Control Module 1 Harness Connector IP29
FE11-5526c
(a)
Disconnect the I/P fuse block wiring harness connector IP02.
(b)
Disconnect the I/P fuse block wiring harness connector IP29.
(c)
Measure resistance between IP02 terminal No.2 and IP29
terminal No.14.
Standard Resistance values: Less than 1 Ω
Is the resistance specified value?
Body Electric
Wipers / Washers System
11-243
No
Check the open circuit between IP02 terminal
No.2 and IP29 terminal No.14.
Yes
Step 9
Replace the body control module (BCM).
(a)
Replace the body control module (BCM). Refer to
.
Confirm the wipers are working correctly.
Yes
System normal
No
Step 10
Measure the I/P fuse block fuse C05 terminal I voltage.
I/P Fuse Harness Connector C05
FE11-5527c
(a)
Turn the ignition switch to the ON position.
(b)
Operate the rear wiper switch to normal position.
(c)
Measure the I/P fuse block fuse C05 terminal I voltage with
a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
Yes
No
Step 11
Replace the I/P fuse block.
(a)
Replace the I/P fuse block.
Confirm the wipers are working correctly.
Yes
System normal
No
Step 12
Repair the circuit between the I/P block C05 terminal I and the rear wiper motor wiring harness connector
terminal No.2.
11-244
Wipers / Washers System
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст