Lexus GS300/400 (2000 year). Manual — part 12
–
AIR CONDITIONING
COMPRESSOR AND MAGNETIC CLUTCH
AC–45
2730
6.
GS400:
INSTALL SUCTION HOSE
Install the suction hose with the bolt and nut.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Hose should be connected immediately after the caps have been removed.
HINT:
Lubricate 2 new O–rings with compressor oil and install them to the hose.
7.
INSTALL DRIVE BELT
(See page
8.
INSPECT DRIVE BELT TENSION
(See page
9.
INSTALL ENGINE UNDER COVER
10.
CONNECT NEGATIVE (–) TERMINAL CABLE TO BATTER
11.
EVACUATE AIR FROM REFRIGERATION SYSTEM AND CHARGE SYSTEM WITH REFRIGERANT
Specified amount: 600
±
50 g (21.16
±
1.76 oz.)
12.
INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak detector, check for leakage of refrigerant.
If there is leakage, check the tightening torque at the joints.
13.
INSPECT A/C OPERATION
AC0WZ–01
AC–46
–
AIR CONDITIONING
CONDENSER
2731
CONDENSER
ON–VEHICLE INSPECTION
1.
INSPECT CONDENSER FINS FOR BLOCKAGE OR DAMAGE
If the fins are clogged, wash them with water and dry with compressed air.
NOTICE:
Be careful not to damage the fins.
If the fins are bent, straighten them with a screwdriver or pliers.
2.
INSPECT CONDENSER AND FITTINGS FOR LEAKAGE OF REFRIGERANT
Using a gas leak detector, check for leakage of refrigerant.
If there is leakage, check the tightening torque at the joints.
AC22B–01
I09253
I09252
I10327
O–Ring
Liquid Tube
Discharge Hose
N·m (kgf·cm, ft·lbf)
: Specified torque
Non–reusable part
Air Cleaner Assembly
Air Cleaner Duct
Condenser
Bracket
Condenser
Dryer
Filter
Cap
O–Ring
10 (100, 7)
10 (100, 7)
12.3 (125, 9)
Compressor oil ND–OIL 8 or equivalent
Radiator Upper Support
–
AIR CONDITIONING
CONDENSER
AC–47
2732
COMPONENTS
AC0X0–01
I02397
I02398
I02399
AC–48
–
AIR CONDITIONING
CONDENSER
2733
REMOVAL
1.
DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, please refer to the following item.
Evacuate air from refrigeration system.
Charge system with refrigerant and inspect for leakage of refrig-
erant.
Specified amount : 600
±
50 g (21.16
±
1.76 oz.)
2.
REMOVE THESE PARTS:
(a)
Air cleaner duct
(b)
Air cleaner assembly
(c)
2 radiator upper supports
3.
DISCONNECT DISCHARGE HOSE AND LIQUID TUBE
Remove the 2 bolts and disconnect the hose and tube.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, please refer to the following item.
Lubricate 2 new O–rings with compressor oil and install them
to the hose and tube.
4.
REMOVE CONDENSER
(a)
Remove the 4 bolts and 2 brackets.
(b)
Push the radiator toward engine.
(c)
Push the condenser toward radiator and pull it upward.
HINT:
At the time of installation, please refer to the following item.
If condenser is replaced, add compressor oil to the condenser.
Add 40 cc (1.4 fl. oz)
Compressor oil: ND – OIL 8 or equivalent
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст