Lexus ES300 (1997 year). Manual — part 143
BO096–01
H02888
Inner LH Cover
Luggage Compartment Trim
Inner RH Cover
Luggage Compartment
RH Rear Floor
Finish Side Plate
Rear Floor
Finish Plate
LH Rear Floor
Finish Side Plate
Reinforcement
Energy Absorber
Rear Bumper Cover
34 (350, 25)
34 (350, 25)
N·m (kgf·cm, ft·lbf)
: Specified torque
–
BODY
REAR BUMPER
BO–5
1183
1997 LEXUS ES300 (RM511U)
REAR BUMPER
COMPONENTS
BO097–03
N21796
Radiator Grille
Hood
Support
Seal
Hood Insulator
Support Seal
Window Washer
Nozzle
Hood Support
Hood Hinge
Hood Hinge
N·m (kgf·cm, ft·lbf) : Specified torque
Window
Washer
Nozzle
Window Washer Hose
26 (265, 19)
Hood Support
17.5 (178, 13)
17.5 (178, 13)
17.5 (178, 13)
17.5 (178, 13)
26 (256, 19)
BO–6
–
BODY
HOOD
1184
1997 LEXUS ES300 (RM511U)
HOOD
COMPONENTS
BO098–01
N03433
Centering Bolt
Bolt with Washer
N21378
N21379
N21380
–
BODY
HOOD
BO–7
1185
1997 LEXUS ES300 (RM511U)
ADJUSTMENT
HINT:
Since the centering bolt is used as the hood hinge and hood
lock set bolt, the hood and hood lock cannot be adjusted with
it on. Substitute the bolt with the washer for the centering bolt.
1.
ADJUST HOOD IN FORWARD/REARWARD AND
LEFT/RIGHT DIRECTIONS
Adjust the hood by loosening the hood side hinge bolts.
Torque: 26 N·m (265 kgf·cm, 19 ft·lbf)
2.
ADJUST FRONT EDGE OF HOOD IN VERTICAL
DIRECTION
Adjust the hood by turning the cushions.
3.
ADJUST HOOD LOCK
Adjust the hood lock by loosening bolts.
Torque:
A bolt: 8.0 N·m (82 kgf·cm, 71 in.·lbf)
B bolt: 11 N·m (112 kgf·cm, 8 ft·lbf)
BO099–01
N21782
150 mm (5.91 in.)
BO–8
–
BODY
HOOD SUPPORT
1186
1997 LEXUS ES300 (RM511U)
HOOD SUPPORT
REPLACEMENT
1.
REMOVE SUPPORT FROM HOOD
Remove the bolt and support from the hood.
HINT:
While supporting the hood with by hand, remove the hood.
2.
REMOVE SUPPORT FROM BODY
Remove the bolt and support.
3.
IF NECESSARY, REPLACE HOOD SUPPORT
NOTICE:
Handling the hood support
Do not disassemble the support because the cylinder
is filled with pressurized gas.
If the support is to be replaced, drill a 2.0 – 3.0 mm
(0.079 – 0.118 in.) hole in the area shown in the il-
lustration to completely release the high–pressure
gas before disposing of it.
When drilling, chips may fly out so work carefully.
The gas is colorless, odorless and non–toxic.
When working, handle the support carefully. Never
score or scratch the exposed part of the piston rod,
and allow any paint or oil to get on it.
Do not turn the piston rod and cylinder with the sup-
port fully extended.
4.
INSTALL HOOD SUPPORT
Install the hood support.
Torque: 17.5 N·m (178 kgf·cm, 13 ft·lbf)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст