Mercedes-Benz ML320. Manual — part 739
Seat belts/belt tensioners
Fig. 70: Identifying Assembly Wedge (115 589 03 59 00)
REMOVING AND INSTALLING SPARE WHEEL COVER - AR68.30-P-4610GH
MODEL 163.174
end fitting (2) of rear seat
belt
1001-01D
9
Remove brackets (4) (2
each.) from lining (8)
10
Open cover (5) and remove
11
Unscrew screw (6)
12
Unscrew screw (7)
13
Remove lining (8)
As of VIN A145273, X708319 up to VIN
A289564, X754619: two clips on inside of paneling
in roof area.
Installation: Check clips and replace if
necessary. Properly insert height adjuster for seat
belt into paneling. Check function Install paneling in
edge molding of floor covering
Long wedge
Fig. 6
14
Pull seat belt out of lining
15
Remove lead from 12V
socket
At right paneling
16
Install in the reverse order
Number
Designation
Model 163 up to 08/99 Model 163 as of 09/99
BA91.40-P-1001-01D Screw on belt end fitting
Nm 35
35
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Fig. 71: Identifying Spare Wheel Cover Components
Wheels
REMOVE/INSTALL PANELING ON B-PILLAR - AR68.30-P-4700GH
Removal, installation
1
Remove cargo space cover
See Owner's Manual.
2
Loosen retaining straps (2) and remove
spare wheel cover front section (1)
3
Remove spare wheel
*BA40.10-P-
1002-01A
4
Remove electric air pump (3)
5
Unscrew screws (4) and remove spare
wheel mount (5)
6
Remove bracket (6)
Turn in clockwise direction until
bracket (6) releases at D-pillar.
7
Remove rear wall on spare wheel cover
2 screws.
8
Install in opposite order
Number
Designation
Model 163.174
BA40.10-P-1002-01A
Bolt for spare wheel on inside of spare wheel mount
Nm 50
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
Fig. 72: Identifying Paneling On B-Pillar Components
Remove/install
Removal
Risk of fracture and cracking
of plastic paneling parts and the
associated clip retainers
1
Remove door sill molding
AR68.30-P-
4100GH
2
Pull off front and rear rubber
door seal in the area of the B-
pillar
3
Unscrew screw for belt end
fitting (1) from seat
*BA91.40-P-
1001-01D
4
Remove bottom paneling (3)
5.1
Remove SRS label and unscrew
screw behind
As of 1.9.01.
6
Unscrew sheet metal screws (4)
from upper paneling
As of 1.9.01: clips are no longer present.
Installation: The lug of the seat belt
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Safety belts/emergency tensioning retractors
REMOVING AND INSTALLING INSIDE REARVIEW MIRROR - AR68.40-P-0001GH
MODEL 163.136 /154 /172 #A up to 145272, 163.136 /154 /172 #X up to 708318
Fig. 73: Identifying Inside Rearview Mirror Components
REMOVE/INSTALL INSIDE REARVIEW MIRROR - AR68.40-P-0001GI
7.1
Unclip top panel (5)
adjusting device (6) must align with the
recess of the paneling. Check mounting clips
and replace if damaged.
8
Install in the reverse order
Number
Designation
Model 163 up to 08/99
Model 163 as of 09/99
BA91.40-P-1001-01D
Belt end fitting screw
Nm 35
35
Remove/install
1
Disconnect connector (H7/1x1) from rear of
inside rearview mirror (H7/1)
Only with code (249a), automatic
dimming inside rearview mirror
2
Remove cable duct (1) from mirror shaft
Only with code (249a), automatic
dimming inside rearview mirror
3
Push cable duct (2) together and remove
Only with code (249a), automatic
dimming inside rearview mirror
4
Turn mirror shaft 90 degrees and pull out of
mirror base (3) downward
Inside rearview mirror is arrested on
mirror base with spring tension
5
Install in the reverse order
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст