Mercedes-Benz ML320. Manual — part 833
S-B-82.70/179A February 2002
2
TDMA PROGRAMMING
1. Obtain the following information from the cellular carrier before beginning the programming sequence:
•
Cellular telephone number: __ __ __ - __ __ __ - __ __ __ __
•
Carrier system I.D.: __ __ __ __ __ (I.D. number will be 1 to 5 digits)
2. Obtain the telephone security code from the customer. In a new telephone, it is set to 000000.
•
Telephone security code: __ __ __ __ __ __ (Default is all zeros)
3. Program as follows:
Step
To
Press (Input)
Phone Displays
1
Enter Programming
Mode
Press: #, Carrier System I.D., #, *,
“SEND”
Enter Security Code
_ _ _ _ _ _
2
Enter Security Code
Press: 0, 0, 0, 0, 0, 0 and select
“OK” (This is the factory default
code)
ESN (Hex)
3
Enter Phone Number
Scroll down to MIN: --- --- --- ----
and insert the ten digit MIN
through the keypad and select
“OK” (MIN is the customer’s
cellular number)
IMSI
4
Finalizing
Programming
Select “DONE” (The handset
display will turn off temporarily)
Main Menu
Note: The telephone will display “Try Again” if an entry error is made. Press “CLR” to erase the
message/incorrect digits or press and hold “CLR” to clear all digits and then enter the correct number
and press “SEND.”
4. The telephone will power off after the “NAM Program Begins” message displays. When the telephone is
powered up again, it will search for the network and be ready for use.
S-B-82.70/179A
February 2002
3
CDMA PROGRAMMING
1. Obtain the following information from the cellular carrier before beginning the programming sequence:
•
Cellular telephone number: __ __ __ - __ __ __ - __ __ __ __
•
Carrier analog system I.D.: __ __ __ __ __ (I.D. number will be 1 to 5 digits)
•
Carrier digital system I.D.: __ __ __ __ __ (I.D. number will be 1 to 5 digits)
Note: Generally, the analog and digital system I.D. numbers will be the same. Questions regarding
system I.D. numbers should be addressed with the cellular carrier.
2. Program as follows:
Step
To
Press (Input)
Telephone Displays
1
Enter
Programming
Mode
Press: 7, 4, 6, 6, 3, #, MENU,
MENU
Nam 1
Nam 2
2
Selecting NAM
Choose “SELECT” for NAM 1
MIN: 0000000000
3
Enter Phone
Number
Insert the ten digit MIN
through the keypad and select
“OK” (This is the customer’s
cellular number)
IMSI
4
Enter AMPS
System I.D.
Scroll down to AMPS Sys ID,
insert the number and select
“OK” (AMPS data is provided
by the carrier)
CDMA
Sys ID:
5
Enter
CDMA
System I.D.
Insert the CDMA Sys ID and
select “OK” (
CDMA
data is
provided by the carrier)
MIN:
6
Finalizing
Programming
Select “DONE” and then press
the “END” key
Main Menu
Note: The telephone will display “Try Again” if an entry error is made. Press “CLR” to erase the
message/incorrect digits or press and hold “CLR” to clear all digits and then enter the correct number
and press “STO.”
3. After the “Entry Done” message appears, the telephone will display “Searching” as it attempts to contact
a network. When the “Searching” message disappears, the telephone is ready for use.
4. To program a second number, follow step 1 in the table below and steps 2-6 in the above table.
Step
To
Press (Input)
Phone Displays
1
Enter NAM2
Programming
Mode
7, 4, 6, 6, 3, #, 2, FCN, FCN
Enter MIN
Note: Be sure to obtain the system I.D. for each before beginning the programming sequence if the
second through fourth numbers are with different cellular carriers.
Note: The CDMA telephone has a two telephone number maximum. Refer to the operation guide for
instructions on how to switch between the various telephone numbers.
AZ82.60-P-0004A
Retrofit vehicle video system
3.10.00
MODELS 163.136 /154 /172 1A as of 145273,
163.136 /154 /172 1X as of 708319,
163.113 /128 /157 /174 /175 1#
left hand drive vehicle
P82.60-2376-08
1
Central interface module
2
Video monitor
3
Video player
B
Video/DVD player wiring harness
C
Wiring harness for video monitor
4
Auxiliary interface module
5
DVD player wiring harness
A2
Radio
P82.60-2399-01
P82.60-2400-01
P82.60-2444-01
6
Antenna cable for FM modulator
7
Vehicle antenna cable
8
Self-adhesive foamed material
9
Antenna cable for FM modulator
Illustrated as of VIN A289565, X754620
13
Auxiliary interface module connector
14
Mount for center console
Illustrated up to VIN A289564, X754619
10
Wiring harness for auxiliary interface
module
11
Clip
12
Self-adhesive foamed material
Remove
1
Remove center console
f
Remove/install center console
AR68.20-P-2000GH
2
Remove center console insulating mat
3
Remove rear air duct
Up to VIN A289564, X754619. 2 screws
at rear air duct.
4
Remove radio (A2)
f
Remove/install radio
AR82.60-P-7502EA
5
Remove glove compartment
f
Remove/install glove compartment
AR68.10-P-1400GI
Torx bit set
*000589011000
6
Loosen upper section of right front door
rubber seal
7
Remove A-pillar paneling on right
f
Remove/install paneling on A-pillar
AR68.30-P-4050GH
Long wedge
*115589035900
8
Remove right sun visor
f
Remove/install sun visor
AR68.60-P-5480GH
9
Remove right front handle
Open covers for handles, press down clip
on each side of handle, at the same time
press handle upward and pull out.
Copyright DaimlerChrysler AG 09.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
10
Remove edge guard for tilting/sliding roof
cutout
11
Release upper right B-pillar paneling
12
Remove covers at lower rear seat
Do NOT remove center cover for lower
40% seat. Do NOT reinstall curtain on 60%
front bench seat.
f
Remove and install cover on bottom of rear
seat
AR91.12-P-1100GH
13
Release side shade at the 60% bench
Fold shade upward so that the working
area is not obstructed.
14
Remove 40% rear seat
f
Remove and install bench
AR91.12-P-1010GI
Torx bit set
*000589011000
Install
15
Retrofit central interface module (1)
AZ82.60-P-0004-01A
16
Insert antenna cable for FM modulator (6) into
vehicle antenna cable (7)
17
Cover connector with self-adhesive foamed
material (8)
18
Plug remaining antenna cable of FM
modulator (9) into radio
19
Install radio (A2)
f
Remove/install radio
AR82.60-P-7502EA
20
Retrofit video monitor (2) and wiring harness
of video monitor (C)
With glass version of electric sliding/tilting
roof, code 414a.
AZ82.60-P-0004-02A
Except glass version of electric
sliding/tilting roof, code 414a.
AZ82.60-P-0004-02B
21
Secure upper right B-pillar paneling
Ensure that the lugs of the seat belt height
adjustment are located correctly in the recess
clearance of the paneling.
22
Install right front handle
23
Install right sun visor
f
Remove/install sun visor
AR68.60-P-5480GH
24
Install right front A-pillar cover
f
Remove/install paneling on A-pillar
AR68.30-P-4050GH
25
Re-secure upper area of rubber door seal
26
Route wiring harness of video/DVD player
(B), additional interface module (4) and wiring
harness of video monitor (C) later
Up to VIN A289564, X754619.
AZ82.60-P-0004-03A
As of VIN A289565, X754620.
AZ82.60-P-0004-03B
27
Retrofit auxiliary interface module (4) in
center console
Up to VIN A289564, X754619.
AZ82.60-P-0004-04A
As of VIN A289565, X754620.
AZ82.60-P-0004-04B
28
Install center console insulating mat
29
Install center console
f
Remove/install center console
AR68.20-P-2000GH
30.1
Plug in plug of additional interface module
and secure the wiring harness of the
additional interface module (10) to the clip
(11) together with the wiring harness of the
rear power windows in the center console
Up to VIN A289564, X754619.
30.2
Insert auxiliary interface module (13)
connector and route between center console
mount (14) and center console.
As of VIN A289565, X754620.
31.1
Secure auxiliary interface module plug in the
left rear corner of the ashtray housing using
self-adhesive foamed material (12)
Up to VIN A289564, X754619.
32
Open ashtray and cup holder and close to
check correct function
33
Attach side shade of the 60% bench
34.1
Retrofit video player (3)
AZ82.60-P-0004-05A
*BA91.12-P-1005-03A
*BA91.12-P-1008-03A
34.2
Retrofit DVD player
AZ82.60-P-0005-01GH
35
Install 40% rear seat
f
Remove and install bench
AR91.12-P-1010GI
Torx bit set
*000589011000
Copyright DaimlerChrysler AG 09.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст