Mercedes-Benz ML320. Manual — part 799
AR91.40-P-0683GH
Removing and installing rear center seat belt
10.3.97
MODEL
163.136 /154 /172 up to 31.8.99
P91.40-0373-06
1
Torx socket bolt
2
Lap belt end fitting
3
Rear seat cover
4
Torx socket bolt
5
Seat belt buckle
Operation no. of operation texts or standard texts and flat rates
Sector
Op. no.
Operation text
P
911107
REPLACING SEAT BELT FOR MIDDLE REAR SEAT
Removing, installing
1
Fold rear seat backrest forward
See Owner's Manual
2
Unscrew screw (1) for seat belt end fitting on
rear seat
Inner Torx screw for seat belt is fastened
to rear bench seat frame.
*BA91.40-P-1001-01D
Torx bit set
*000589011000
3
Pull lap belt end fitting (2) down and out on
rear seat
4
Pull clip channel for rear seat cover (3) off of
right side of seat frame
5
Remove screw (4) on belt buckle
*BA91.40-P-1006-01D
Torx bit set
*000589011000
6
Pull belt buckle (5) down and out
Check seat belt and belt buckle for
damage.
7
Install in the reverse order
Installation: Ensure they are installed
free of stress. Do not install seat belt twisted.
Seat belts/emergency tensioning retractors
Number
Designation
Model
163 up to
08/99
Model
163 as of
09/99
BA91.40-P-1001-01D
Screw on seat belt end fittings
Nm
35
35
BA91.40-P-1006-01D
Bolt of seat belt buckle to rear seat
Nm
35
45
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
Torx bit set
000 589 01 10 00
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
AR91.40-P-0681GH
Removing and installing rear seat belts
13.3.97
MODELS 163.136 /154 /172 up to 31.8.99
P91.40-0360-06
1
Bolt
2
Seat belt guide bracket
3
Bolt
4
Automatic belt retractor
5
Belt height adjuster
Operation no. of operation texts or standard texts and flat rates
Sector
Op. no.
Operation text
P
911087
REPLACING SEAT BELT FOR LEFT REAR SEAT
P
911097
REPLACING SEAT BELT FOR RIGHT REAR SEAT
P
911112
REPLACING SEAT BELTS (BOTH) FOR REAR SEAT
Removing, installing
Danger!
Risk of injury through expansion of
automatic belt retractor spring
Never dismantle automatic belt retractor.
AS91.00-Z-0002-01A
1
Remove paneling on C-pillar
AR68.30-P-4490GH
2
Remove bolt (1) on seat belt guide bracket (2)
If necessary remove belt height adjuster
(5) .
*BA91.40-P-1002-01D
3
Remove bolt (3) on automatic belt retractor (4)
*BA91.40-P-1003-01D
4
Remove automatic belt retractor (4)
During installation: Note catch of
automatic belt retractor.
5
Check seat belts for damage
e
AP91.40-P-9150GH
6
Install in the reverse order
Seatbelts/emergency tensioning retractors
Number
Designation
Model
163 up to
08/99
Model
163 as of
09/99
BA91.40-P-1002-01D
Screw in rear upper belt guide fitting
Nm
30
30
BA91.40-P-1003-01D
Screw, on rear automatic belt retractor
Nm
30
30
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
SI91.12-P-0001GH
Service Information: Bowden cables for rear seat
30.5.03
MODELS 163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
40 % rear seat
The Bowden cables for vertical and horizontal adjustment at the
40 % rear seat now can be individually replaced. The new routing
assignment must be observed when replacing the Bowden cables.
The connection at the release handle and at the rear seat support
remain the same.
P91.12-2598-11
1
Cable, vertical adjustment
2
Cable, horizontal adjustment
3
Clip
4
Rubber straps
f
Remove and install cables for rear seat
adjustment
Models 163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
40 % rear seat
AR91.12-P-1130GH
Parts ordering notes
Part no.
Designation
Quantity
163 920 04 64 38
Cable, horizontal adjustment
1
163 920 12 80
Cable, vertical adjustment
1
000 995 18 14
Clip
1
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст