Mercedes-Benz ML320. Manual — part 798
AR91.40-P-1516GH
Remove/install rear seat belt buckle
12.1.00
MODEL
163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /175 except CODE (293) Left and right rear side bag
40% rear seat
P91.40-2172-01
1
Bolt
2
Rear seat seat belt buckle
Remove/install
1
Fold down 60% rear seat
See Operating Instructions
2
Fold backrest of 40% rear seat forwards
See Operating Instructions
3
Remove side covers on rear seat seat belt
buckle
4
Unscrew bolt (1) from rear seat seat belt
buckle (2)
*BA91.40-P-1006-01D
5
Remove rear seat seat belt buckle (2)
Installation: Check rear seat seat belt
buckle for damage.
6
Install in the reverse order
Seat belts/emergency tensioning retractors
Number
Designation
Model
163 as of
09/99
BA91.40-P-1006-01D
Bolt, belt buckle to rear seat
Nm
45
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
AR91.40-P-1516GK
Remove/install rear seat belt buckle
26.9.02
MODEL
163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /175 with CODE (293) Left and right rear side airbag
40% rear seat
MODEL
163.174
40% Rear seat
P91.40-2172-01
P91.18-2030-01
P91.40-2173-01
1
Bolt
2
Rear seat seat belt buckle
3
Connector
8
Adhesive tape
4
Lower cover
6
Retaining straps
7
Electrical line for rear seat seat belt
buckle
Remove/install
1
Fold down 60% rear seat
See Operating Instructions
2
Fold backrest of 40% rear seat forwards
See Operating Instructions
3
Remove side covers on rear seat seat belt
buckle
4
Unscrew bolt (1) from rear seat seat belt
buckle (2)
*BA91.40-P-1006-01D
5
Turn ignition key to "0" position
To avoid fault codes.
6
Disconnect connector (3) from electrical line
of rear seat seat belt buckle
7.1
Remove lower cover (4)
Only with 3rd seat row, code 847.
8
Remove retaining straps (6)
9
Unhook rear seat cover on reverse side and
pull out electrical line for rear seat seat belt
buckle (7) on rear seat cushion
Loosen adhesive tape (8).
Installation: Route electrical line for rear
seat seat belt buckle (7) correctly and fasten
to rear seat cushion frame using new
adhesive tape (8).
10
Remove rear seat seat belt buckle (2)
Installation: Check rear seat seat belt
buckle for damage.
11
Install in the reverse order
Seat belts/emergency tensioning retractors
Number
Designation
Model
163 as of
09/99
BA91.40-P-1006-01D
Bolt, belt buckle to rear seat
Nm
45
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
AR91.40-P-0683GI
Remove, replace and install rear center seat belt
4.5.99
MODELS 163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
P91.40-2170-09
Remove/Install
Danger!
The spring in the inertia reel can pose an
injury hazard when the tension is released
and it uncoils.
Never disassemble inertia reels
AS91.00-Z-0002-01A
1.1
Disconnect connector from electrical line of
seat belt buckle of the outer rear seat
Only with side airbag in the rear (left and
right), code 293.
Turn ignition key into position "0" in order to
avoid fault codes.
2
Unhook rear seat cover on the back of the
rear seat cushion
3
Carefully lift up rear seat cover and unscrew
bolt from belt end fitting
Do not damage rear seat cover.
Installation: Align rear seat cushion and
rear seat cover correctly.
*BA91.40-P-1001-01D
Torx bit set
*000589011000
4
Remove belt end fitting from rear seat
5
Detach paneling (1) of belt guide (2) from rear
backrest
Lift up front paneling and remove
6
Unscrew mounting screws of belt guide and
remove belt guide (2)
7
Fold rear backrest forwards
See Operating Instructions
8
Unhook rear backrest cover (3) on the back of
the rear backrest
9
Unscrew bolts (5) of rear wall paneling (4)
10
Remove rear wall covering (4)
Pull at the upper corners of the rear wall
paneling in order to remove
body-bound rivets (10).
Installation: Replace body-bound rivets.
11
Unscrew bolt (6) from automatic belt retractor
(7)
*BA91.40-P-1005-01D
Torx bit set
*000589011000
12
Detach automatic belt retractor (7) and guide
seat belt through the rear backrest cover of
the rear backrest
Installation: Pay attention to catch and
correct installation position of the automatic
belt retractor. Make sure seat belt is not
twisted when installed.
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
13
Check seat belt for signs of damage
e
Check seat belts for damage
AP91.40-P-9150GH
14
Install in the reverse order
Seat belts/emergency tensioning retractors
Number
Designation
Model
163 as of
09/99
BA91.40-P-1001-01D
Screw on belt end fitting
Nm
35
BA91.40-P-1005-01D
Screw rear seat belt retractor to 2/3 seat
bench
Nm
40
Torx bit set
000 589 01 10 00
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст