Mercedes-Benz ML320. Manual — part 736
Safety belts/emergency tensioning retractors
Luggage nets
Child seats
Fig. 57: Identifying Assembly Wedge (110 589 03 59 00)
Fig. 58: Identifying Torx Bit Set (000 589 01 10 00)
REMOVE/INSTALL PANELING IN FOOTWELL - AR68.30-P-4010GH
MODELS 163.113 /128 /136 /154 /157 /172 /174 /175
rear-end door.
8
Remove floor covering (3) to rear
Installation: Install floor covering
below side paneling.
Assembly wedge
Fig. 57
9
Install in the reverse order
Number
Designation
Model 163 up to 08/99
Model 163 as of 09/99
BA91.40-P-1001-01D
Belt end fitting screw
Nm 35
35
Number
Designation
Model Series
163
BA68.50-P-1001-
02A
Bolt securing cargo retainer bracket to loading compartment
floor
Nm 24
Number
Designation
Model Series 163
BA91.20-P-1001-01A Bracket for child seat anchorage on load compartment floor Nm 24
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Fig. 59: Identifying Paneling In Footwell
REMOVING AND INSTALLING PANELING ON A-PILLAR - AR68.30-P-4050GH
MODELS 163.113 /128 /136 /154 /157 /172 /174 /175
Vehicle illustrated up to 31.8.98
Remove/install
1
Remove front door sill molding cover (1)
2
Unscrew screws from door sill molding on rocker panel
Only two front screws.
3
Pull off door seal (2) in the area of driver's side paneling (3) or
front passenger's side paneling (4)
4
Unscrew screw (5) for engine hood release lever (6) on A-pillar
Driver's side only.
5
Unhook engine hood cable and remove engine hood release
lever (6)
Driver's side only.
6.1
Rotate locks (7) on the cover of the fuse and relay box (8) 1/4
revolution counterclockwise into the vertical position
As of 09.99. Passenger
side only.
7.1
Pull back cover of fuse and relay box (8) (arrow) and remove
As of 09.99. Passenger
side only.
8.1
Unscrew nut (9)
As of 09.99. Passenger
side only.
9
Unclip driver's side paneling (3) and front passenger's side
paneling (4) and remove
Lift door sill molding
slightly to allow removal.
10
Install in the reverse order
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Fig. 60: Identifying Paneling On A-Pillar
Remove/install
1
Remove door rubber
seal (2) in area of A-
pillar
2.1
Remove cap (3)
Up to 08/98.
3.1
Unscrew screw (4)
Up to 08/98.
4
Remove A-pillar
paneling (1)
The paneling is fastened in the instrument panel at the bottom
with lugs and will be fastened with a clip at top as of 09/98.
Installation: Replace clip
Long wedge
Fig.
6
5
Install in the reverse
order
On vehicles up to 08/98, on which a new paneling should be
installed, the upper area of the fixing opening at the top of the A-
pillar must be enlarged so that the clip retainer of the paneling can
be installed in the A-pillar.
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Fig. 61: Identifying Long Wedge (115 589 03 59 00)
REMOVE/INSTALL DOOR SILL MOLDING - AR68.30-P-4100GH
MODELS 163.113 /128 /136 /154 /157 /172 /174 /175
Fig. 62: Identifying Door Sill Molding
Remove/install
1
Remove covers (2) from door
sill molding (1) upward
Up to 08/99: Start at center of covers so that
retaining lugs of covers are not damaged.
As of 09/99: Start at the front of the front covering
and the rear of the rear covering in order not to damage
the retaining lugs.
Unscrew screws (3) on door sill
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Interior Equipment - 163 Chassis
me
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст