Mazda 6. Manual — part 201
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–46–3
K
SELECTOR CABLE ADJUSTMENT
A6E561646102W02
1. Remove the center console.
2. Shift the selector lever to P position.
3. Unlock the lock piece of the selector cable
(selector lever side) in the order shown in the
figure.
4. Verify that the manual shaft is in P position.
5. Lock the lock piece of the selector cable (selector
lever side) in the order shown in the figure.
6. Install the center console.
7. Shift the selector lever from P position to L range,
and make sure that there are no other
components in that area to interfere with the lever.
End Of Sie
SELECTOR LEVER REMOVAL/INSTALLATION
A6E561646102W03
1. Disconnect the negative battery cable.
2. Remove battery and battery tray.
3. Remove the air cleaner compornent. (See
F–10 INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
4. Remove the console.
5. Remove the dashboard compleat.
(See
S–82 DASHBOARD REMOVAL/INSTALLATION
6. Remove the SAS control module.
(See
T–124 SAS UNIT REMOVAL/INSTALLATION
.)
7. Remove the climate control unit. (See
U–44 CLIMATE CONTROL UNIT REMOVAL
.) (See
8. Remove the rear heat duct. (See
U–23 REAR HEAT DUCT REMOVAL/INSTALLATION
9. Remove in the order shown in the figure.
10. Remove the battery, battery tray and battery bracket.
End Of Sie
A6E5616W003
A6E5616W004
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–47
K
KAUTOMATIC TRANSAXLE
1. Install in the reverse order of removal.
.
AUTOMATIC TRANSAXLE SHIFT MECHANISM
A6E5616W005
1
Column cover(with key interlock)
2
Clip(with key interlock)
3
Clip(with key interlock)
4
Interlock cable(with key interlock)
(See
K–49 Interlock Cable Installation Note
5
Selector cable
(See
K–48 Selector Cable Removal Note
(See
K–48 Selector Cable Installation Note
.)
6
Selector lever
K–48
AUTOMATIC TRANSAXLE SHIFT MECHANISM
Selector Cable Removal Note
1. Remove the clip.
2. Remove the selector cable.
Selector Cable Installation Note
1. Install the selector cable to the selector lever certainly.
2. Install the selector cable to the bracket certainly.
Note
• Step 3, 4 is for the selector cable
replacement only.
3. Verify that the selector lever is in P position.
4. Lock the lock piece of the selector cable (selector
lever side) in the order shown in the figure.
5. Verify that the manual shaft is in P position.
A6E5616W006
A6E5616W020
A6E5616W004
A6E5616W007
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–49
K
Caution
• Bending the selector cable in the manner
shown in the figure will damage the cable
and it may become loose when shifted.
When installing the selector cable, hold it
straight.
Note
• Install the selector lever to the manual shaft
lever with the spring side of the selector
cable end facing the front of the vehicle.
6. Install the selector lever to the manual shaft lever
so that no load acts on the selector cable.
7. Confirm that the tip of the manual shift lever projects out of the end of the selector cable.
8. Install the selector cable to the selector cable securely bracket.
Interlock Cable Installation Note
1. Install the interlock cable as shown in the figure.
Caution
• Position the sponge protector so that it is
not crushed or squeezed by the SAS unit.
• If the interlock and selector cables cross
over each other, position the interlock
cable to pass over the selector cable.
2. Push the snap pin (or a
φ1.5 round bar or
simular.) into hole A by fully pushing the slider pin
in.
3. Push the snap pin into hole B and hole C of the
lock unit until it passes through.
4. Disconnect the brake switch connector.
5. Remove the brake switch. (See
.)
6. Install the new brake switch. (See
.)
Caution
• Do not connect the brake switch
connector until the interlock cable is
installed.
7. With the slider pin pressed, slide the lock unit to
fix the lock unit hook into the bracket hole
securely as shown in the figure.
Caution
• Allowing the interlock cable to be bent or
twisted during installation can affect the
lock unit operation.
8. Rotate the slider pin to release the lock, and verify
that the it slides freely.
A6E5616W008
SAS UNIT WIRING HARNESS
SAS UNIT
SELECTOR
CABLE
INTERLOCK
CABLE
SPONGE PROTECTOR
A6E5616L001
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
CHU0514W012
SLIDER PIN
LOCK UNIT
BRACKET
BHE0514W007
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст