Mazda 6. Manual — part 200
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–45
K
SHIFT-LOCK INSPECTION
A6E561630000W01
1. Turn the ignition switch to ON position.
2. Verify that the selector lever is in P position.
3. Depress the brake pedal and verify that the selector lever can be shifted from P position.
• If a malfunction is found, inspect the interlock cable.
(See
K–45 INTERLOCK CABLE INSPECTION
.)
End Of Sie
KEY INTERLOCK INSPECTION
A6E561609000W01
1. Verify that the ignition key cannot be pulled out except in P position.
• If a malfunction is found, inspect the interlock cable. (See
K–45 INTERLOCK CABLE INSPECTION
End Of Sie
INTERLOCK CABLE INSPECTION
A6E561609000W02
1. Turn the ignition switch to ON position (engine OFF).
2. Remove the clip of the selector lever base plate,
then remove the interlock cable from the U-
groove.
3. Remove the interlock cable from the selector
lever.
4. Verify that the interlock cable moves freely with
the brake pedal depressed.
• If there is any malfunction, replace the
interlock cable.
AUTOMATIC TRANSAXLE SHIFT MECHANISM
A6E5616W011
A6E5616W010
INTERLOCK CABLE
BHE0514W009
K–46
AUTOMATIC TRANSAXLE SHIFT MECHANISM
End Of Sie
INTERLOCK CABLE ADJUSTMENT
BHE051409000W03
1. Turn the ignition switch to ON position (engine OFF).
2. Pull up the lock piece of the interlock cable to
release the lock.
3. Remove the clip of the selector lever base plate,
then remove the interlock cable from the U-
groove.
4. Remove the interlock cable from the selector
lever.
5. Fully pull the end of the interlock cable to the
selector lever.
6. Remove the lock unit from the bracket.
7. Verify that the markings on the slider pin and the
lock unit are aligned.
End Of Sie
A6E5616W010
A6E5616W011
INTERLOCK CABLE
CHU0514W010
INTER LOCK UNIT
SLIDE PIN
MARKING
MARKING
BHE0514W010
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–46–1
K
K–46
AUTOMATIC TRANSAXLE
INTERLOCK CABLE ADJUSTMENT
BHE051409000W03A
8. Push the snap pin (or a
φ1.5 round bar or
simular.) into hole A by fully pushing the slider pin
in.
9. Push the snap pin into hole B and hole C of the
lock unit until it passes through.
10. Disconnect the brake switch connector.
11. Remove the brake switch. (See
.)
12. Install the new brake switch. (See
.)
Caution
• Do not connect the brake switch
connector until the interlock cable
adjustment is completed.
13. Install the lock unit to the bracket. (See
K–49 Interlock Cable Installation Note
14. Rotate the slider pin to release the lock, and verify that the it slides freely.
15. Verify that the slider pin contacts the brake pedal
stopper rubber and rotate the slider pin to lock.
16. Install the interlock cable end onto the interlock
link on the selector lever.
17. Fit the interlock cable in the U-groove in the
selector lever base plate and install the clip.
AUTOMATIC TRANSAXLE SHIFT MECHANISM
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
CHU0514W012
STOPPER
RUBBER
SLIDER PIN
MARKING
MARKING
BHE0514W011
A6E5616W010
A6E5616W011
K–46–2
AUTOMATIC TRANSAXLE SHIFT MECHANISM
18. Press the interlock cable lock piece in until it is
locked.
Caution
• Applying a load to the interlock cable
while pressing the lock piece in can
affect the lock unit operation.
19. Remove the snap pin from the lock unit hole A, B
and C.
20. Connect the brake switch connector with the
brake pedal released.
Caution
• The clearance between the brake switch
and the brake pedal is automatically
adjusted to the correct amount when the
brake switch connector is connected
after the brake switch has been properly
installed. If the brake switch is not
properly installed or the connector is
connected before installation, the
clearance may be incorrect, causing a brake light malfunction. Therefore, always verify that the
brake switch is properly installed before connecting the connector.
• Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again.
Therefore, replace the switch with a new one when replacing the power brake unit or the pedal, or
performing any procedure that changes the pedal stroke.
21. Inspect shift lock operation. (See
End Of Sie
SELECTOR LEVER INSPECTION
A6E561646102W01
1. Turn the ignition switch to ON (engine OFF).
2. With the brake pedal depressed, verify that there is a "click" at each range when shifted.
3. Verify that the selector lever can be shifted.
4. Verify that there is a "click" at each position when
shifted from P position to L range.
5. Verify that the positions of the selector lever and
the indicator are aligned.
• If not as specified, adjust the TR switch.(See
K–18 TRANSAXLE RANGE (TR) SWITCH
ADJUSTMENT
6. Verify that the vehicle operates in each selected
range.
End Of Sie
LOCK PIECE
INTERLOCK CABLE
UNLOCK
LOCK
A6E5616W012
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
CHU0514W012
A6E5616W002
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст