Mazda 6. Manual — part 202
K–50
AUTOMATIC TRANSAXLE SHIFT MECHANISM
9. Pull the slider pin outward until it contacts the
brake pedal stopper rubber and rotate the slider
pin to lock.
10. Verify that the shift the selector lever in P position.
11. Install the interlock cable end onto the cam pin on
the selector lever.
12. Fit the interlock cable in the U–groove in the
selector lever base plate, and install the clip.
13. Press the interlock cable lock piece in until it is
locked.
Caution
• Applying a load to the interlock cable
while pressing the lock piece in can
affect the lock unit operation.
14. Remove the snap pin from the lock unit hole A, B
and C.
End Of Sie
STOPPER
RUBBER
SLIDER PIN
MARKING
MARKING
BHE0514W011
A6E5616W010
A6E5616W011
A6E5616W012
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
CHU0514W012
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–50–1
K
K–50AUTOMATIC TRANSAXLE
SELECTOR LEVER REMOVAL/INSTALLATION
A6E561646102W03B
Interlock Cable Installation Note
15. Connect the brake switch connector with the brake pedal released.
Caution
• The clearance between the brake switch and the brake pedal is automatically adjusted to the
correct amount when the brake switch connector is connected after the brake switch has been
properly installed. If the brake switch is not properly installed or the connector is connected
before installation, the clearance may be incorrect, causing a brake light malfunction. Therefore,
always verify that the brake switch is properly installed before connecting the connector.
• Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again.
Therefore, replace the switch with a new one when replacing the power brake unit or the pedal, or
performing any procedure that changes the pedal stroke.
16. Turn the ignition switch to ON position.
17. Install the interlock cable to the key cylinder.
18. Slide the outer casing to the key cylinder, and
insert the clip over the convex part of the outer
casing.
End Of Sie
AUTOMATIC TRANSAXLE SHIFT MECHANISM
A6E5616W014
AUTOMATIC TRANSAXLE SHIFT MECHANISM
K–51
K
KAUTOMATIC TRANSAXLE
SELECTOR LEVER DISASSEMBLY/ASSEMBLY
A6E561646102W04
1. Disassemble in the order shown in the figure.
2. Assemble in the reverse order of disassembly.
.
Connector Disassembly Note
1. Insert a thin piece of metal from the terminal side
of the connector, and press down the terminal
locking tab.
2. Pull the terminal out of the connector.
End Of Sie
AUTOMATIC TRANSAXLE SHIFT MECHANISM
A6E5616W015
1
K–51 Connector Disassembly Note
.)
2
Selector lever knob component
3
Cover
4
Indicator panel
5
Selector illumination light
6
Selector lever
A6E5616W016
K–52
ON-BOARD DIAGNOSTIC
FOREWORD
A6E567001030W01
• When the customer reports a vehicle malfunction, check the malfunction indicator lamp (MIL), HOLD indicator
light flashing, and PCM memory for diagnostic trouble code (DTC), then diagnose the malfunction according to
following flowchart.
— If the DTC exists, diagnose the applicable DTC. (See
.)
— If the DTC does not exist, MIL does not illuminate, and HOLD indicator light flashes, diagnose the
applicable symptom troubleshooting. (See
K–113 SYMPTOM TROUBLESHOOTING ITEM TABLE
*:Malfunction indicator lamp (MIL), HOLD indicator light
End Of Sie
AUTOMATIC TRANSAXLE ON-BOARD DIAGNOSTIC FUNCTION
A6E567001030W02
DTC Reading Procedure
(See
.)
End Of Sie
AFTER REPAIR PROCEDURE
A6E567001030W03
Caution
• After repairing a malfunction, perform this procedure to verify that the malfunction has been
corrected.
• When this procedure is carried out, be sure to drive the vehicle at lawful speed and pay attention
to the other vehicles.
1. Connect the WDS or equivalent to the DLC-2.
2. Turn the ignition key to ON (engine OFF).
3. Verify that DTCs are cleared from memory.
4. Decrease ATF temperature to 20
°C {68 °F} or below.
5. Start the engine then wait 180 seconds or more.
6. Warm up the engine and ATX.
• Engine coolant temperature: 60 °C {140 °F} or above.
• Transaxle fluid temperature: 20 °C {68 °F} or above.
7. Shift the selector lever between P position to L range while depressing brake pedal.
8. Drive the vehicle for 150 seconds or more at a vehicle speed between 25 and 59 km/h {15 and 36 mph},
then 60 km/h {37 mph} or more for 100 seconds or more.
ON-BOARD DIAGNOSTIC
A6E5670W013
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст