Mazda 6. Manual — part 324
T–56
WIPER AND WASHER
WINDSHIELD WIPER MOTOR REMOVAL/INSTALLATION
A6E811667340W01
1. Disconnect the negative battery cable.
2. Remove the windshield wiper arm and blade. (See
T–57 WINDSHIELD WIPER ARM AND BLADE REMOVAL/
3. Remove the cowl grille. (See
S–50 COWL GRILLE REMOVAL/INSTALLATION
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Adjust the windshield wiper arm and blade. (See
T–58 WINDSHIELD WIPER ARM AND BLADE
ADJUSTMENT
End Of Sie
WINDSHIELD WIPER MOTOR DISASSEMBLY/ASSEMBLY
A6E811667340W02
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
Windshield Wiper Link Removal Note
1. Pry off the connection between the windshield wiper motor and windshield wiper link.
End Of Sie
WINDSHIELD WIPER MOTOR INSPECTION
A6E811667340W03
L.H.D.
1. Disconnect the windshield wiper motor connector.
2. Connect battery positive voltage to terminal E or
D and ground to terminal B, and inspect the
operation of the windshield wiper motor as
indicated below.
3. Disconnect battery positive voltage from terminal
E of the motor while the wipers are operating.
4. Verify that the wipers do not stop in the park
position.
5. Short between the motor terminals A and D and
connect battery positive voltage to the motor terminal C.
6. Verify that the wipers operate at low speed again, then stop in the park position.
• If not as specified, replace the windshield wiper motor.
WIPER AND WASHER
1
Connector
2
Bolt
3
Windshield wiper motor
A6E8116W102
1
Windshield wiper link (See
2
Bolt
3
Windshield wiper motor
A6E8116W140
Terminal
Operation
E
High
D
Low
A6E8116W127
WIPER AND WASHER
T–57
T
R.H.D.
1. Disconnect the windshield wiper motor connector.
2. Connect battery positive voltage to terminal B or
A and ground to terminal D, and inspect the
operation of the windshield wiper motor as
indicated below.
3. Disconnect battery positive voltage from terminal
B of the motor while the wipers are operating.
4. Verify that the wipers do not stop in the park
position.
5. Short between the motor terminals E and A and
connect battery positive voltage to the motor terminal C.
6. Verify that the wipers operate at low speed again, then stop in the park position.
• If not as specified, replace the windshield wiper motor.
End Of Sie
WINDSHIELD WIPER ARM AND BLADE REMOVAL/INSTALLATION
A6E811667320W01
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. Adjust the windshield wiper arm and blade. (See
T–58 WINDSHIELD WIPER ARM AND BLADE
ADJUSTMENT
Windshield Wiper Arm Installation Note
1. Clean the windshield wiper arm connector shafts
using a wire brush before installing the windshield
wiper arms.
End Of Sie
Terminal
Operation
B
High
A
Low
A6E8116W128
1
Cap
2
Nut
3
Windshield wiper arm (See
)
4
Windshield wiper blade
5
Rubber brush
A6E8116W111
A6E8116W103
T–58
WIPER AND WASHER
WINDSHIELD WIPER ARM AND BLADE ADJUSTMENT
A6E811667320W02
1. Operate the windshield wiper motor to set the wipers in the park position.
2. Set the windshield wiper arms height as shown.
End Of Sie
WASHER TANK REMOVAL/INSTALLATION
A6E811667481W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
A6E8116W107
1
Bolt
2
Connector
3
Washer hose
4
Clip
5
Headlight cleaner hose
6
Washer tank
A6E8116W117
WIPER AND WASHER
T–59
T
WINDSHIELD WASHER MOTOR REMOVAL/INSTALLATION
A6E811676670W01
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
WINDSHIELD WASHER MOTOR INSPECTION
A6E811676670W02
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
)
3. Connect battery positive voltage to the motor
terminal B and ground to the motor terminal A.
4. Verify that the windshield washer motor operates.
• If the motor does not operate, replace the
windshield washer motor.
End Of Sie
WASHER FLUID-LEVEL SENSOR REMOVAL/INSTALLATION
A6E811676670W03
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
)
3. Remove the headlight cleaner motor. (See
T–69 HEADLIGHT CLEANER MOTOR REMOVAL/INSTALLATION
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
End Of Sie
1
Windshield washer motor
2
Grommet
A6E8116W123
A6E8116W129
1
Connector
2
Washer fluid-level sensor
3
Grommet
A6E8116W114
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст