Mazda 6. Manual — part 325
T–60
WIPER AND WASHER
WASHER FLUID-LEVEL SENSOR INSPECTION
A6E811676670W04
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
3. Insoect for continuity between the washer fluid-
level sensor terminals using an ohmmeter.
4. Verify that the windshield washer motor operates.
• If not as specified, replace the washer fluid-
level sensor.
End Of Sie
WINDSHIELD WASHER NOZZLE REMOVAL/INSTALLATION
A6E811667510W01
1. Remove the bonnet insulator.
2. Remove the windshield washer hose from the windshield washer nozzle.
3. Compress the hooks of the windshield washer nozzle.
4. Pull the windshield washer nozzle out to remove
it.
5. Install in the reverse order of removal.
End Of Sie
WINDSHIELD WASHER NOZZLE CLEANING
A6E811667510W03
1. Clean the washer nozzle by inserting and moving
a needle or an equivalent tool back and forth.
• If the nozzle becomes clogged again after
cleaning, remove the hose from washer
nozzle. Make sure there is enough washer
fluid. Then turn the washer switch on and
flush the inside of the hose.
End Of Sie
A6E8116W130
A6E8116W144
A6E8116W143
A6E8116W124
WIPER AND WASHER
T–61
T
WINDSHIELD WASHER HOSE REMOVAL/INSTALLATION
A6E811650601W01
1. Remove the bonnet insulator.
2. Partially peel off the right side mud guard.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
REAR WASHER MOTOR REMOVAL/INSTALLATION
A6E811676672W01
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
REAR WASHER MOTOR INSPECTION
A6E811676672W02
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
)
3. Connect battery positive voltage to the terminal B and ground to the terminal A of the motor.
4. Verify that the rear washer motor operates.
• If the motor does not operate, replace the rear
washer motor.
End Of Sie
1
Clip
2
Joint pipe
3
Windshield washer hose
A6E8116W126
1
Rear washer motor
2
Grommet
A6E8116W104
A6E8116W131
T–62
WIPER AND WASHER
REAR WIPER MOTOR REMOVAL/INSTALLATION
A6E811667450W01
1. Disconnect the negative battery cable.
2. Remove the rear wiper arm and blade. (See
T–63 REAR WIPER ARM AND BLADE REMOVAL/
3. Remove the liftgate lower trim. (See
S–95 LIFTGATE LOWER TRIM REMOVAL/INSTALLATION
)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Adjust the rear wiper arm and blade. (See
REAR WIPER ARM AND BLADE
ADJUSTMENT
End Of Sie
REAR WIPER MOTOR INSPECTION
A6E811667450W02
1. Disconnect the negative battery cable.
2. Remove the liftgate lower trim. (See
S–95 LIFTGATE LOWER TRIM REMOVAL/INSTALLATION
)
3. Disconnect the rear wiper motor connector.
4. Connect battery positive voltage to the rear wiper motor terminal A and the ground to a bare metal part of the
vehicle and the rear wiper motor terminal B.
5. Verify that the rear wiper motor operates.
6. Disconnect the ground to the terminal B while the
rear wiper is operating.
1
Connector
2
Outer bushing
3
Bolt
4
Rear wiper motor
A6E8116W110
A6E8116W119
A6E8116W132
WIPER AND WASHER
T–63
T
7. Verify that the rear wiper stops in the park
position.
• If not as specified, replace the rear wiper
motor.
End Of Sie
REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION
A6E811667420W01
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. Adjust the rear wiper arm and blade. (See
REAR WIPER ARM AND BLADE
ADJUSTMENT
Rear Wiper Arm Installation Note
1. Clean the rear wiper arm connector shaft using a
wire brush before installing the rear wiper arm.
End Of Sie
A6E8116W119
A6E8116W133
1
Cap
2
Nut
3
Rear wiper arm (See
)
4
Rear wiper blade
5
Rubber brush
A6E8116W112
A6E8116W103
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст