Mazda 6. Manual — part 283
POWER WINDOW SYSTEM
S–27
S
Except driver’s side
1. Turn the power-cut switch to UNLOCK.
2. Inspect for continuity between the power window main switch terminals using an ohmmeter.
• If not as specified, replace the power window main switch.
End Of Sie
A6E7716W009
S–28
POWER WINDOW SYSTEM
POWER WINDOW SUBSWITCH INSPECTION
A6E771666370W01
1. Inspect for continuity between the power window
subswitch terminals.
• If not as specified, replace the power window
subswitch.
End Of Sie
POWER WINDOW REGULATOR REMOVAL/INSTALLATION
A6E771658560W01
1. Disconnect the negative battery cable.
2. Remove the front door glass/rear door glass.
3. Remove the front door speaker/rear door speaker.
4. Remove the power window motor.
5. Remove the nuts.
6. Insert hand through the speaker installation hole,
rotate the regulator drum housing in the direction
shown in the figure and disengage the regulator
drum housing from the door unit connection
hooks.
A6E7716W011
A6E7716W013
A6E7716W005
A6E7716W006
POWER WINDOW SYSTEM
S–29
S
7. Remove the power window regulator from the
speaker installation hole.
8. Install in the reverse order of removal.
End Of Sie
POWER WINDOW MOTOR REMOVAL/INSTALLATION
A6E771659560W01
1. Disconnect the negative battery cable.
2. Remove the front door trim or rear door trim.
3. Disconnect the power window motor connector.
4. Remove the bolts.
5. Remove the power window motor from the power
window regulator drum.
6. Install in the reverse order of removal.
Note
• When installing the power window motor to
the power window regulator drum, the drum
housing hook may come off the door unit. If
this happens, remove the door speaker,
insert your hand in the speaker installation
hole, connect the drum housing hooks, and
while supporting the drum housing, install
the power window motor to the drum.
End Of Sie
POWER WINDOW MOTOR INSPECTION
A6E771659560W02
Driver’s Side
1. Disconnect the power window motor connector.
2. Apply battery positive voltage to the power
window motor terminals E and F and inspect the
operation the power window motor operation.
• If not as specified, replace the power window
motor.
3. Apply battery positive voltage to the power
window motor terminal D and connect terminal C
to ground.
4. Measure the voltage at terminal B and A while performing Step 3.
• If not as specified, replace the power window motor.
Voltage
Pulse wave: MAX. 5 V, MIN. 0 V
A6E7716W007
A6E7716W004
Motor operation
Terminal
F
E
UP
GND
B+
DOWN
B+
GND
A6E7716W008
S–30
POWER WINDOW SYSTEM, POWER DOOR LOCK SYSTEM
Except Driver's Side
1. Apply battery positive voltage to the power
window motor terminals and inspect the operation
of the power window motor.
• If not as specified, replace the power window
motor.
End Of Sie
FRONT DOOR LOCK ACTUATOR INSPECTION
A6E771858310W01
Door Lock Actuator
1. Disconnect the front door lock actuator connector.
2. Apply battery positive voltage to the front door
lock actuator terminals and inspect the operation
of the front door lock actuator.
• If not as specified, replace the front door lock
actuator.
With double locking system
( ) : RH
Without double locking system
( ) : RH
Motor operation
Terminal
F
E
UP
GND
B+
DOWN
B+
GND
A6E7716W010
POWER DOOR LOCK SYSTEM
Actuator operation
Connection
B+
GND
Lock
A
(F)
C
(D)
Double lock
A
(F)
B
(E)
Unlock
C and B
(D and E)
A
(F)
Actuator operation
Connection
B+
GND
Lock
A
(F)
B
(E)
Unlock
A
(F)
B
(E)
A6E7718W011
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст