Mazda 6. Manual — part 296
SLIDING SUNROOF
S–79
S
SUNROOF MOTOR REMOVAL
A6E774069870W01
1. Disconnect the negative battery cable.
2. Remove the headliner.
3. Disconnect the connector.
4. Remove the screws, and then remove the sunroof
motor.
End Of Sie
SUNROOF MOTOR INSTALLATION
A6E774069870W02
1. Connect the sunroof motor connector.
2. Connect the sunroof switch connector.
3. Connect the negative battery cable.
4. Turn the ignition switch to ON position.
5. Press the CLOSE side of the slide switch until the sunroof motor stops.
6. Disconnect the sunroof switch connector.
7. Install the screws, and then install the sunroof motor.
8. Install the headliner.
End Of Sie
SUNROOF MOTOR INSPECTION
A6E774069870W03
Motor
1. Remove the sunroof motor.
2. Apply battery positive voltage to the sunroof motor terminals and inspect the operation of the sunroof motor.
• If not as specified, replace the sunroof motor.
A6E7740W002
Connection
Motor operation
2A
2B
B+
GND
Turn left (Slide close/Tilt up)
GND
B+
Turn right (Slide open/Tilt down)
A6E7740W016
S–80
SLIDING SUNROOF
Limit Switch
S–96 HEADLINER REMOVAL/INSTALLATION
2. Verify the glass panel position.
3. Disconnect the connector.
4. Inspect for continuity between the sunroof motor terminals using an ohmmeter.
• If not as specified, replace the sunroof motor.
End Of Sie
SUNROOF RELAY INSPECTION
A6E774069873W01
Note
• Sunroof relay is built in the sunroof motor.
S–96 HEADLINER REMOVAL/INSTALLATION
2. Connect the sunroof switch connector.
3. Measure the voltage at the sunroof relay terminals as indicated below.
4. Disconnect the sunroof relay connector before inspecting for continuity at terminal 1G.
• If not as specified, inspect the parts listed under “Action” and the related wiring harnesses.
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the sunroof
relay.
5. Connect the negative battery cable.
Terminal voltage list (Reference)
A6E7740W020
A6E7740W021
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
1A
Tilt down
Sunroof switch
Sunroof is tilting down. (Not
including position when fully
closed)
0
• Inspect sunroof switch
(See
• Inspect related harness
Other
B+
1B
IG2
Sunroof motor
Ignition switch is at ON
position.
B+
• Inspect A/C 15 A fuse
• Inspect sunroof switch
(See
• Inspect related harness
Other
0
1C
—
—
—
—
—
1D
Slide close
Sunroof switch
Sunroof is closing. (Including
position when fully closed and
open)
0
• Inspect sunroof switch
(See
• Inspect related harness
Other
B+
1E
—
—
—
—
—
A6E7740W019
SLIDING SUNROOF
S–81
S
End Of Sie
SUNROOF SWITCH REMOVAL/INSTALLATION
A6E774066560W01
Note
• The sunroof switch is together with the map light.
1. Disconnect the negative battery cable.
2. Remove the map light from the headliner.
3. Install in the reverse order of removal.
End Of Sie
SUNROOF SWITCH INSPECTION
A6E774066560W02
1. Remove the sunroof switch.
2. Inspect for continuity between the sunroof switch terminals using an ohmmeter.
• If not as specified, replace the sunroof switch.
End Of Sie
1F
Slide open
Sunroof switch
Sunroof is fully opening.
0
• Inspect sunroof switch
• Inspect related harness
Other
B+
1G
Sunroof relay
ground
GND
Under any condition: inspect
for continuity to ground.
Yes
• Inspect related harness
1H
Tilt up
Sunroof switch
Sunroof is tilting up. (Including
position when fully closed)
0
• Inspect sunroof switch
• Inspect related harness
Other
B+
2A
Slide close/
tilt up
Sunroof motor
Sunroof is opening/tilting
down.
0
• Inspect sunroof switch
• Inspect sunroof motor
• Inspect related harness
Sunroof is closing/tilting up.
B+
Other
0
2B
Slide open/tilt
down
Sunroof motor
Sunroof is opening/tilting
down.
B+
• Inspect sunroof switch
• Inspect sunroof motor
• Inspect related harness
Sunroof is closing/tilting up.
0
Other
0
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
A6E7740W022
A6E7740W023
S–82
DASHBOARD AND CONSOLE
DASHBOARD REMOVAL/INSTALLATION
A6E774255100W01
1. Disconnect the negative battery cable.
2. Remove the glove compartment.
3. Remove the console.
4. Remove the meter hood.
5. Remove the instrument cluster.
6. Remove the column cover.
7. Remove the lower panel.
8. Remove the steering shaft.
9. Remove the A-pillar trims.
10. Remove the front scuff plates.
11. Remove the front side trims.
12. Remove the side panels.
13. For vehicles equipped with the wire-type climate control unit, disconnect the wires for the front A/C unit. (See to
U–44 CLIMATE CONTROL UNIT REMOVAL
U–45 CLIMATE CONTROL UNIT INSTALLATION
14. Disconnect the dashboard harness connectors.
15. Remove the bolts.
Warning
• Removing the dashboard without
supporting it can be dangerous. The
dashboard may fall and injure you.
Always perform these procedures
together with at least another person.
16. Pull out the support pins from the body to remove
the dashboard.
17. Take the dashboard off from the driver-side door
opening.
18. Install in the reverse order of removal.
End Of Sie
DASHBOARD AND CONSOLE
A6E7742W004
A6E7742W005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст