Mazda 6. Manual — part 297
DASHBOARD AND CONSOLE
S–83
S
DASHBOARD DISASSEMBLY/ASSEMBLY
A6E774255100W02
1. Remove the passenger-side air bag module.
2. Remove the ventilator grilles.
3. Remove the audio unit.
4. Remove the climate control unit.
5. Disassemble in the order indicated in the table.
6. Assemble in the reverse order of disassembly.
.
End Of Sie
SIDE PANEL REMOVAL/INSTALLATION
A6E774264960W01
1. Disengage clips using a tape-wrapped flathead
screwdriver.
2. Pull the side panel toward you, then disengage
tabs from dashboard, and remove the side panel.
3. Install in the reverse order of removal.
End Of Sie
A6E7742W003
1
Dashboard harness
2
Dashboard member
3
Damper
4
Dashboard
A6E7742W010
S–84
DASHBOARD AND CONSOLE
COLUMN COVER REMOVAL/INSTALLATION
A6E774260200W01
1. Detach the fit of the upper column cover from the
meter hood rubber.
2. Remove the upper column cover.
3. Remove the ignition key illumination.
4. Remove the screws.
5. Remove the lower column cover.
6. Install in the reverse order of removal.
End Of Sie
METER HOOD REMOVAL/INSTALLATION
A6E774255420W01
1. Remove the screws.
2. Pull the meter hood toward you, then detach the
column cover.
3. Install in the reverse order of removal.
End Of Sie
LOWER PANEL REMOVAL/INSTALLATION
A6E774264280W01
1. Remove the bonnet release lever.
2. Remove the screws.
3. Pull the lower panel toward you, then disengage
clips A and tabs B from the dashboard, and
remove the lower panel.
4. Install in the reverse order of removal.
End Of Sie
A6E7742W008
A6E7742W002
A6E7742W009
DASHBOARD AND CONSOLE
S–85
S
CENTER BOX REMOVAL/INSTALLATION
A6E774264030W01
1. Disconnect the negative battery cable.
2. Remove the center panel module.
3. Remove the screws.
4. Pull the center box forward, then disengage the
tabs
5. Disconnect the LDC unit connector.
6. Install in the reverse order of removal.
End Of Sie
GLOVE COMPARTMENT REMOVAL/INSTALLATION
A6E774264030W02
1. Pull the stay damper to the direction shown in the
figure. Then detach the fit for the glove
compartment from the stay damper.
2. Bend the stoppers inward to remove.
3. Turn the glove compartment downward and pull
the clips to remove it.
4. Install in the reverse order of removal.
End Of Sie
A6E7742W012
A6E7742W006
A6E7742W007
S–86
DASHBOARD AND CONSOLE
CONSOLE REMOVAL/INSTALLATION
A6E774264270W01
Applied VIN (assumed):
JMZ GG12
✻✻✻# 100001—190206
JMZ GG14
✻✻✻# 100001—190206
JMZ GY19
✻✻✻# 100001—137241
JMZ GY89
✻✻✻# 100001—137241
1. For MT vehicle, remove the shift lever knob.
2. Slightly bend back the cradle. (with car-navigation
system)
3. Remove the cup holder panel using a tape-
wrapped screwdriver.
4. Remove the boot panel using a tape-wrapped
screwdriver, disconnect the cigarette lighter
connector, and remove the front ashtray
illumination.
5. Remove the bolts.
6. Install in the reverse order of removal.
Applied VIN (assumed):
JMZ GG12
✻✻✻# 190207—
JMZ GG14
✻✻✻# 190207—
JMZ GY19
✻✻✻# 137242—
JMZ GY89
✻✻✻# 137242—
1. For MT vehicle, remove the shift lever knob.
2. Rotate the wiring harness clip installed on the cradle 90
° in the direction indicated by the arrow in the figure and
pull it out. (with car-navigation system)
3. Disconnect the cradle connector.
4. Remove the boot panel using a tape-wrapped screwdriver, disconnect the cigarette lighter connector, and
remove the front ashtray illumination.
5. Remove the bolts.
6. Install in the reverse order of removal.
End Of Sie
A6E7742W011
90
°
CRADLE
BOOT PANEL
CUP HOLDER PANEL
TAB
BOLT
CONSOLE
TAB
TAB
HARNESS
CLIP
CRADLE
CONNECTOR
CRADLE
HARNESS
CLIP
A6J7742L350
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст