Mazda 6. Manual — part 111
OIL PRESSURE INSPECTION
D–3
D
OIL PRESSURE INSPECTION
A6E331001003W01
Warning
• Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your
skin by washing with soap and water immediately after working with engine oil.
• Hot engines and engine oil can cause severe burns. Turn off the engine and wait until it and the
engine oil have cooled.
1. Remove the under cover.
2. Remove the oil pressure switch.
3. Screw the SST into the oil pressure switch
installation hole.
4. Warm up the engine to normal operating
temperature.
5. Run the engine at the specified speed, and note
the gauge readings.
• If the pressure is not as specified, inspect for
the cause and repair or replace as necessary.
Note
• The oil pressure can vary with oil viscosity
and temperature.
Oil pressure [Oil temperature: 100
°C{212°F}]:
L8, LF :
234—521 kPa {2.39—5.31 kgf/cm
2
,33.9—
75.5 psi} min. [ 3,000rpm]
L3 :
395—649 kPa {4.03—6.61 kgf/cm
2
, 57.3—
94.1 psi} min. [ 3,000rpm]
6. Stop the engine and wait until it is cool.
7. Remove the SST.
Caution
• Any sealant stuck at the end of the oil pressure switch can cause operation malfunction of the oil
pressure switch.
Be sure there is no sealant at the end of the oil pressure switch.
8. Apply silicone sealant to the oil pressure switch
threads as shown.
9. Install the oil pressure switch.
Tightening torque:
12—18 N·m {1.2—1.8 kgf·m, 9—13 ft·lbf}
10. Install the under cover.
11. Start the engine and inspect for oil leakage.
• If the oil leaks, specify the faulty part and
repair or replace it.
End Of Sie
OIL PRESSURE INSPECTION
AME3310W001
AME3310W002
D–4
ENGINE OIL
ENGINE OIL INSPECTION
A6E331214001W01
1. Position the vehicle on level ground.
2. Warm up the engine to normal operating temperature.
3. Stop the engine and wait for 5 min.
4. Remove the dipstick.
5. Verify that the oil level is between the F and L marks on the dipstick and check the engine oil condition.
• If the oil level is below the L mark, add the oil.
End Of Sie
ENGINE OIL REPLACEMENT
A6E331214001W02
Warning
• Hot engines and engine oil can cause severe burns. Turn off the engine and wait until it and the
engine oil has cooled.
• A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall,
causing death or serious injury. Never work around or under a lifted vehicle if it is not securely
supported on safety stands.
• Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your
skin by washing with soap and water immediately after working with engine oil.
Caution
• In case you spill engine oil on the front pipe, wipe it off completely. If you fail to wipe the spilled
oil, it will produce a white smoke because of the heat.
1. Position the vehicle on level ground.
2. Remove the oil filler cap .
3. Remove the under cover.
4. Remove the oil pan drain plug.
5. Drain the engine oil into a container.
6. Install the oil pan drain plug.
• With washer
1. Install the oil pan drain plug with a new washer.
Tightening torque
30—41 N·m {3.1—4.1 kgf·m, 23—30 ft·lbf}
• Without washer
1. Inspect the seal rubber of the oil pan drain plug and make sure there are no cracks or damage.
— If necessary, replace the oil pan drain plug.
2. Clean the flange surface (seal rubber) on the oil pan drain plug, then install the oil pan drain plug.
Tightening torque
22—30 N·m {2.2—3.1 kgf·m, 16—22 ft·lbf}
Note
• The amount of residual oil in the engine can vary according to the replacement method, oil temperature, etc.
Verify the oil level after engine oil replacement.
7. Refill the engine with the specified type and amount of engine oil.
Oil capacity (Approximate quantity)
L {US qt, Imp qt}
*
: Always verify the oil level with the dipsticks since the engine oil capacity differs according to dipstick
specifications.
ENGINE OIL
Item
Engine
L8
LF
L3 *
Total (dry engine)
4.6 {4.8, 4.0}
4.6 {4.8, 4.0}
Dipstick A: 4.2 {4.4, 3.7}
Dipstick B: 5.1 {5.4, 4.5}
Oil replacement
3.9 {4.0, 3.4}
3.9 {4.0, 3.0}
Dipstick A: 3.1 {3.3, 2.7}
Dipstick B: 4.0 {4.2, 3.5}
Oil and oil filter
replacement
4.3 {4.5, 3.8}
4.3 {4.5, 3.8}
Dipstick A: 3.5 {3.7, 3.1}
Dipstick B: 4.4 {4.6, 3.9}
ENGINE OIL
D–5
D
Note
• The maintenance intervals on scheduled maintenance table (See
) can only be supported by the use of following oils.
Recommended engine oil
8. Refit the oil filler cap.
9. Start the engine and inspect for oil leakage.
• If the oil leaks, specify the faulty part and repair or replace it.
10. Inspect the oil level.
• If necessary, add oil. (See
11. Install the under cover.
End Of Sie
A6E0110W001
DIPSTICK A
DIPSTICK B
TWIST
NO TWIST
Item
Market
Europe
Except Europe
Grade
API SL
ACEA A3
API SG, SH, SJ, SL
ILSAC GF-2, GF-3
Viscosity (SAE)
5W-30
10W-40
5W-20
40, 30, 20,
20W-20, 10W-30,
10W-40, 10W-50,
20W-40, 15W-40,
20W-50, 15W-50,
5W-20, 5W-30
Remarks
Mazda genuine Dexelia oil e.g.
—
—
D–6
OIL FILTER
OIL FILTER REPLACEMENT
A6E331414300W01
Warning
• Continuous exposure with USED engine oil has caused skin cancer in laboratory mice. Protect
your skin by washing with soap and water immediately after this work.
• Hot engines and engine oil can cause severe burns. Turn off the engine and wait until it and the
engine oil have cooled.
Caution
• To avoid damage to the oil filter, use only specified oil filter.
Cartridge Type
1. Remove the under cover.
2. Loosen the oil filter drain plug. (Do not remove.)
3. Loosen the filter cover for 1 turn using a
commercially available, cap-type oil filter wrench
(diameter- 74 mm {2.9 in}, 14 sided).
4. Remove the oil filter drain plug, and drain the
engine oil.
Note
• Oil could be easily drained when the air is in
the filter.
5. Loosen the oil filter cover for another 1 turn.
6. Remove the oil filter cover and the oil filter.
7. Use a clean rag to wipe off the mounting surface
on the oil filter adapter and the oil filter cover.
8. Apply clean oil to a new O-ring of the oil filter
cover.
9. Apply clean oil to a new O-ring of the oil filter
drain plug.
10. Install the oil filter, oil filter drain plug, and oil filter
cover.
11. Tighten the oil filter cover and the oil filter drain
plug.
Tightening torque
Oil filter cover: 30—35 N·m
{3.1—3.5 kgf·m, 22.2—25.8 ft·lbf}
Oil filter drain plug: 9—10 N·m
{91.8—101.9 kgf·cm, 79.6—88.4 in·lbf}
12. Remove the dipstick and verify that the oil level is
MIN and MAX marks on the dipstick.
• If the oil level is below the MIN mark, add oil.
13. Start the engine and inspect for oil leakage.
14. Inspect the oil level.
• If necessary, add oil. (See
15. Install the under cover.
End Of Sie
OIL FILTER
AME3314W001
AME3314W002
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст