Mazda 6. Manual — part 110
VARIABLE VALVE TIMING, OIL CONTROL VALVE (OCV)
B–33
B
Variable Valve Timing Actuator Removal Note
1. Set a wrench or equivalent tool at the hexagonal part of the camshaft to prevent rotation.
2. Loosen the variable valve timing actuator tightening bolts.
Variable Valve Timing Actuator Installation Note
1. Set a wrench or equivalent tool at the hexagonal part of the camshaft to prevent rotation.
2. Tighten variable valve timing actuator tightening bolts.
Tightening torque
69—75N·m {7.10—7.6 kgf·m, 50.9—55.3 ft·lbf}
End Of Sie
OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION
A6E222614420W01
L3
1. Disconnect the negative battery cable.
2. Remove the plug hole plate.
3. Remove the high-tension lead. (See
G–10–1 HIGH-TENSION LEAD REMOVAL/INSTALLATION
.)
4. Remove the oil control valve (OCV) connector.
5. Remove the ventilation hose.
6. Remove the cylinder head cover. (See
B–17 Cylinder Head Cover Installation Note
7. Remove in the order indicated in the table.
8. Install in the reverse order of removal.
.
End Of Sie
OIL CONTROL VALVE (OCV) INSPECTION
A6E222614420W02
L3
Coil Resistance Inspection
1. Disconnect the negative battery cable.
2. Disconnect the oil control valve connector.
3. Measure the resistance between terminals A and
B using an ohmmeter.
• If not as specified, replace the oil control
valve.
Specification
6.9—7.9 ohms
4. Connect the oil control valve connector.
OIL CONTROL VALVE (OCV)
1
Oil control valve (OCV)
AME2226W001
AME2226W002
B–34
OIL CONTROL VALVE (OCV)
Spool Valve Operation Inspection
1. Disconnect the negative battery cable.
2. Remove the oil control valve.
3. Verify that the spool valve in the oil control valve
is in the maximum valve timing retard position as
indicated in the figure.
• If not as specified, replace the oil control
valve.
4. Verify that the battery is fully charged.
• If not as specified, recharge the battery.
5. Apply battery positive voltage between the oil
control valve terminals and verify that the spool
valve operates and moves to the maximum valve
timing advance position.
• If not as specified, replace the oil control
valve.
Note
• When applying battery positive voltage between the oil control valve terminals, the connection can be
either of the following:
— Positive battery cable to terminal A, negative battery cable to terminal B
— Positive battery cable to terminal B, negative battery cable to terminal A
6. Stop applying battery positive voltage and verify
that the spool valve returns to the maximum valve
timing retard position.
• If not as specified, replace the oil control
valve.
End Of Sie
AME2226W003
AME2226W004
D–1
D
D
LUBRICATION SYSTEM
LOCATION INDEX . . . . . . . . . . . . .D-2
LOCATION INDEX. . . . . . . . . . . ...D-2
OIL PRESSURE INSPECTION . . . . . . . ..D-3
OIL PRESSURE INSPECTION. . . . . . . D-3
ENGINE OIL . . . . . . . . . . . . . . ...D-4
ENGINE OIL INSPECTION. . . . . . . . ..D-4
ENGINE OIL REPLACEMENT. . . . . . . .D-4
OIL FILTER. . . . . . . . . . . . . . . .D-6
OIL FILTER REPLACEMENT . . . . . . . ..D-6
OIL COOLER . . . . . . . . . . . . . . ..D-7
OIL COOLER REMOVAL/INSTALLATION . . ..D-7
OIL PAN. . . . . . . . . . . . . . . . ..D-8
OIL PAN REMOVAL/INSTALLATION. . . . ..D-8
D–2
LOCATION INDEX
LOCATION INDEX
A6E330001002W01
.
End Of Sie
LOCATION INDEX
AME3300W001
1
Oil filter
(See
2
Oil cooler
(
LF and L3 engine models)
(See
3
Oil pan
(See
D–8 OIL PAN REMOVAL/INSTALLATION
4
Oil pump
(See
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст