Mazda 6. Manual — part 368
ON-BOARD DIAGNOSTIC [AIR BAG SYSTEM]
T–219
T
Diagnostic procedure
End Of Sie
STEP
INSPECTION
ACTION
1
INSPECT CRASH ZONE SENSOR
• Check following PID/DATA monitor, using
SST (WDS or equivalent).
(See
— OD_F_CRSH
• Is crash zone sensor normal?
Yes
Present malfunction diagnosis:
• Replace SAS unit.
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
• Troubleshooting completed.
No
Go to next step.
2
INSPECT WIRING HARNESS BETWEEN
CRASH ZONE SENSOR AND SAS UNIT
Warning
• Handling air bag system components
improperly can accidentally deploy air
bag modules and pre-tensioner seat
belts, which may seriously injure you.
Read AIR BAG SYSTEM SERVICE
WARNINGS before handling air bag
system components.
(See
• Turn ignition switch to LOCK position.
• Disconnect negative battery cable and wait
for more than 1 minute.
• Remove column cover.
• Disconnect clock spring connector.
• Remove glove compartment.
• Disconnect passenger-side air bag module
connector.
• Disconnect driver and passenger-side side
air bag module connectors. (Vehicle with
side air bag)
• Disconnect driver and passenger-side
curtain air bag module connectors. (Vehicle
with curtain air bag)
• Remove B-pillar lower trim. (Vehicle with pre-
tensioner seat belt)
• Disconnect driver and passenger-side pre-
tensioner seat belt connectors. (Vehicle with
pre-tensioner seat belt)
• Turn up floor covering.
• Disconnect all SAS unit connectors.
• Disconnect crash zone sensor connector.
• Connect negative battery cable.
• Inspect following wiring harnesses between
SAS unit and crash zone sensor terminals
for short to ground, short to power supply,
and open circuit:
— 1B—A
— 1C—B
• Is wiring harness okay?
Yes
Replace crash zone sensor, then go to next step.
(See
T–123 CRASH ZONE SENSOR REMOVAL/
)
No
Replace wiring harnesses.
3
INSPECT SAS UNIT
• Turn ignition switch to LOCK position.
• Disconnect negative battery cable and wait
for more than 1 minute.
• Connect all SAS unit connectors.
• Connect crash zone sensor connector.
• Is DTC B2296 indicated?
Yes
Present malfunction diagnosis:
• Replace SAS unit.
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
• Troubleshooting completed.
No
Troubleshooting completed.
T–220
ON-BOARD DIAGNOSTIC [AIR BAG SYSTEM]
DTC B2444, U2017
A6E817401046W20
Diagnostic procedure
DTC
B2444
Driver-side side air bag sensor system (sensor internal circuit abnormal)
U2017
Driver-side side air bag sensor system (communication error)
DETECTION
CONDITION
Warning
• Detection conditions are for understanding DTC outline before performing inspection.
Performing inspection with only detection conditions may cause injury due to operating error
or damage the system. When performing inspection, always follow inspection procedure.
• Malfunction in wiring harness between driver-side side air bag sensor and SAS unit
• Malfunction in driver-side side air bag sensor circuit
POSSIBLE
CAUSE
• Open or short circuit in wiring harness between driver-side side air bag sensor and SAS unit
• Driver-side side air bag sensor malfunction
• SAS unit malfunction
STEP
INSPECTION
ACTION
1
INSPECT DRIVER-SIDE SIDE AIR BAG
SENSOR
• Check following PID/DATA monitor, using
— OD_D_CRSH
• Is driver-side side air bag sensor normal?
Yes
Present malfunction diagnosis:
• Replace SAS unit.
(See
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
• Troubleshooting completed.
No
Go to next step.
ON-BOARD DIAGNOSTIC [AIR BAG SYSTEM]
T–221
T
End Of Sie
2
INSPECT WIRING HARNESS BETWEEN
DRIVER-SIDE SIDE AIR BAG SENSOR AND
SAS UNIT
Warning
• Handling air bag system components
improperly can accidentally deploy air
bag modules and pre-tensioner seat
belts, which may seriously injure you.
Read AIR BAG SYSTEM SERVICE
WARNINGS before handling air bag
system components.
(See
• Turn ignition switch to LOCK position.
• Disconnect negative battery cable and wait
for more than 1 minute.
• Remove column cover.
• Disconnect clock spring connector.
• Remove glove compartment.
• Disconnect passenger-side air bag module
connector.
• Disconnect driver and passenger-side side
air bag module connectors. (Vehicle with
side air bag)
• Disconnect driver and passenger-side
curtain air bag module connectors. (Vehicle
with curtain air bag)
• Remove B-pillar lower trim.
• Disconnect driver and passenger-side pre-
tensioner seat belt connectors. (Vehicle with
pre-tensioner seat belt)
• Turn up floor covering.
• Disconnect all SAS unit connectors.
• Disconnect driver-side side air bag sensor
connector.
• Connect negative battery cable.
• Inspect following wiring harnesses between
SAS unit and driver-side side air bag sensor
terminals for short to ground, short to power
supply, and open circuit:
— 2Z—A
— 2AA—B
• Is wiring harness okay?
Yes
Replace driver-side side air bag sensor, then go to next
step.
(See
T–123 SIDE AIR BAG SENSOR REMOVAL/
)
No
Replace wiring harnesses.
3
INSPECT SAS UNIT
• Turn ignition switch to LOCK position.
• Disconnect negative battery cable and wait
for more than 1 minute.
• Connect all SAS unit connectors.
• Connect driver-side side air bag sensor
connector.
• Are DTCs B2444 and/or U2017 indicated?
Yes
Present malfunction diagnosis:
• Replace SAS unit.
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
• Troubleshooting completed.
No
Troubleshooting completed.
STEP
INSPECTION
ACTION
T–222
ON-BOARD DIAGNOSTIC [AIR BAG SYSTEM]
DTC B2445, U2018
A6E817401046W21
Diagnostic procedure
DTC
B2445
Passenger-side side air bag sensor system (sensor internal circuit abnormal)
U2018
Passenger-side side air bag sensor system (communication error)
DETECTION
CONDITION
Warning
• Detection conditions are for understanding DTC outline before performing inspection.
Performing inspection with only detection conditions may cause injury due to operating error
or damage the system. When performing inspection, always follow inspection procedure.
• Malfunction in wiring harness between passenger-side side air bag sensor and SAS unit
• Malfunction in passenger-side side air bag sensor circuit
POSSIBLE
CAUSE
• Open or short circuit in wiring harness between passenger-side side air bag sensor and SAS unit
• Passenger-side side air bag sensor malfunction
• SAS unit malfunction
STEP
INSPECTION
ACTION
1
INSPECT PASSENGER-SIDE SIDE AIR BAG
SENSOR
• Check following PID/DATA monitor, using
— OD_P_CRSH
• Is passenger-side side air bag sensor
normal?
Yes
Present malfunction diagnosis:
• Replace SAS unit.
(See
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
• Troubleshooting completed.
No
Go to next step.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст