Mazda 6. Manual — part 319
T–36
EXTERIOR LIGHTING SYSTEM
2. Pleace the bracket in the proper position as
shown in the figure and press it to the trunk lid
(liftgate) to attach.
End Of Sie
HIGH-MOUNT BRAKE LIGHT REMOVAL/INSTALLATION
A6E811251580W01
4SD
In-vehicle-type
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
Rear spoiler type
1. Disconnect the negative battery cable.
2. Remove the rear spoiler. (See
S–54 REAR SPOILER REMOVAL/INSTALLATION
)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
A6E8112W121
1
Connector
2
High-mount brake light
3
Socket
4
High-mount brake light bulb
A6E8112W123
1
Bolt
2
Cover
2
High-mount brake light (See
A6E8112W115
EXTERIOR LIGHTING SYSTEM
T–37
T
High-mount brake light removal note
1. Tie a string to the end of the connector of the
high-mount brake light beforehand so that the
connector can be passed easily through the rear
spoiler during installation.
5HB
1. Disconnect the negative battery cable.
2. Remove the liftgate lower trim. (See
S–95 LIFTGATE LOWER TRIM REMOVAL/INSTALLATION
)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
LICENSE PLATE LIGHT REMOVAL/INSTALLATION
A6E811251270W01
1. Disconnect the negative battery cable.
2. Remove the rear finisher. (See
S–54 REAR FINISHER REMOVAL/INSTALLATION
)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
COMBINATION SWITCH REMOVAL/INSTALLATION
A6E811266120W01
1. Disconnect the negative battery cable.
2. Remove the driver-side air bag module. (See
T–120 DRIVER-SIDE AIR BAG MODULE REMOVAL/
3. Remove the steering wheel. (See
N–7 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION
.)
4. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
5. Remove the clock spring. (without DSC) (See
T–125 CLOCK SPRING REMOVAL/INSTALLATION
A6E8112W116
1
Connector
2
Nut
3
High-mount brake light
4
Lens
5
Socket
6
High-mount brake light bulb
A6E8112W142
1
Connector
2
License plate light
3
Lens
4
License plate light bulb
A6E8112W108
T–38
EXTERIOR LIGHTING SYSTEM
6. Remove in the order indicated in the table.
7. Install in the reverse order of removal.
End Of Sie
COMBINATION SWITCH DISASSEMBLY/ASSEMBLY
A6E811266120W02
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
End Of Sie
1
Connector
2
Screw
3
Combination switch
A6E8112W102
1
Screw
2
Wiper and washer switch (Light switch)
3
Light switch (Wiper and washer switch)
4
Body
A6E8112W103
EXTERIOR LIGHTING SYSTEM
T–39
T
STEERING ANGLE SENSOR INSPECTION
A6E811266120W03
With DSC
1. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
2. Disconnect the steering angle sensor connector.
3. Connect battery positive voltage to terminal A and ground to terminal F of the steering angle sensor.
4. Turn the steering wheel to the right and left, and
verify that the voltage and pulses at the terminals
are as shown in the figure.
• If not as specified, replace the body of the
combination switch.
End Of Sie
LIGHT SWITCH REMOVAL/INSTALLATION
A6E811266121W01
1. Disconnect the negative battery cable.
2. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
A6E8112W143
1
Connector
2
Screw
3
Light switch
A6E8112W112
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст