Mazda 6. Manual — part 326
T–64
WIPER AND WASHER
REAR WIPER ARM AND BLADE ADJUSTMENT
A6E811667420W02
1. Operate the rear wiper motor to set the wiper in the park position.
2. Set the rear wiper arm onto the ceramics end line.
End Of Sie
REAR WASHER NOZZLE REMOVAL/INSTALLATION
A6E811667511W01
1. Disconnect the negative battery cable.
2. Remove the liftgate upper trim. (See
S–94 LIFTGATE UPPER TRIM REMOVAL/INSTALLATION
3. Remove the rear washer hose from the rear washer nozzle.
4. Compress the tabs of the rear washer nozzle.
5. Pull the rear washer nozzle out to remove it.
6. Install in the reverse order of removal.
7. Adjust the rear washer nozzle. (See
End Of Sie
REAR WASHER NOZZLE ADJUSTMENT
A6E811667511W02
1. Insert a needle or an equivalent tool into the spray
hole of the rear washer nozzle and adjust the
nozzle direction as shown.
End Of Sie
REAR WASHER NOZZLE CLEANING
A6E811667511W03
1. Clean the rear washer nozzle. (See
T–60 WINDSHIELD WASHER NOZZLE CLEANING
End Of Sie
A6E8116W109
A6E8116W105
A6E8116W108
WIPER AND WASHER
T–65
T
REAR WASHER HOSE REMOVAL/INSTALLATION
A6E811667470W01
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See
T–58 WASHER TANK REMOVAL/INSTALLATION
)
3. Partially peel off the right side mud guard.
4. Remove rear washer hose No.1 from the clips.
5. Remove rear washer hose No.1 and joint pipe A.
6. Remove the A-pillar trim. (See
7. Remove rear washer hose No.2 from clip A.
8. Remove clips B from the body.
9. Remove rear washer hose No.2 and joint pipes B.
10. Remove the C-pillar trim. (See
11. Remove the liftgate upper trim. (See
LIFTGATE UPPER TRIM REMOVAL/
INSTALLATION
12. Remove rear washer hose No.3 from clip C.
13. Remove clips D from the body.
14. Remove rear washer hose No.3 and joint pipe C.
15. Remove the headliner. (See
16. Remove the tape from rear washer hose No.4.
17. Install in the reverse order of removal.
End Of Sie
A6E8116W148
A6E8116W149
A6E8116W201
A6E8116W202
T–66
WIPER AND WASHER
INTERMITTENT REAR WIPER RELAY REMOVAL/INSTALLATION
A6E811666810W01
5HB
1. Disconnect the negative battery cable.
2. Remove the trunk side trim. (See
S–92 TRUNK SIDE TRIM REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
INTERMITTENT REAR WIPER RELAY INSPECTION
A6E811666810W02
1. Connect the connector to the intermittent rear wiper relay.
2. Connect the negative battery cable.
3. Measure the voltage at the intermittent rear wiper relay using voltmeter.
• When inspecting terminal D for continuity, disconnect the intermittent rear wiper relay connector.
4. If the value are not as specified in the Terminal Voltage List (Reference), inspect the parts under “Action” and
related wiring harnesses.
5. If the system does not work properly even though the parts or related wiring harnesses do not have any
malfunction, replace the intermittent rear wiper relay.
Terminal Voltage Table (Reference)
1
Connector
2
Bolt
3
Interittent rear wiper relay
A6E8116W101
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
A
Autostop
Rear wiper motor
Rear wiper is operating (INT
position or ON position)
Alternates 0
and B+
• Inspect R. WIP 10 A
fuse
• Inspect wiper and
washer switch (See
68 WIPER AND
WASHER SWITCH
INSPECTION
• Inspect rear wiper
motor (See
• Inspect related harness
Other
B+
D
GND
GND
Under any condition: inspect for
continuity to ground
Yes
• Inspect GND
• Inspect related harness
A6E8116W134
WIPER AND WASHER
T–67
T
End Of Sie
WIPER AND WASHER SWITCH REMOVAL/INSTALLATION
A6E811666122W01
1. Disconnect the negative battery cable.
2. Remove the column cover. (See
S–84 COLUMN COVER REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
G
Rear wiper
switch INT
Rear wiper switch
Ignition switch at
ON position
Rear wiper
switch at INT
position
0
• Inspect R. WIP 10 A
fuse
• Inspect wiper and
washer switch (See
68 WIPER AND
WASHER SWITCH
INSPECTION
• Inspect related harness
• Rear wiper
switch at
OFF position
• Rear wiper
switch at ON
position
B+
I
IG 2
R. WIP 10 A fuse
Ignition switch at ON position
B+
• Inspect R. WIP 10 A
fuse
• Inspect related harness
Other
0
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
1
Connector
2
Screw
3
Wiper and washer switch
A6E8116W203
A6E8116W204
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст