Mazda 6. Manual — part 301
S–98
HEADLINER
SUNVISOR REMOVAL/INSTALLATION
A6E774669270W01
1. Remove the screws, then the sunvisor.
2. Disengage the center adapter (sunvisor stopper)
from the body using a fastener remover.
3. Install in the reverse order of removal.
End Of Sie
A6E7746W005
YTA7746W103
FLOOR COVERING
S–99
S
FRONT FLOOR COVERING REMOVAL/INSTALLATION
A6E774868670W01
1. Disconnect the negative battery cable.
2. Remove the front seats. (See
S–105 FRONT SEAT REMOVAL/INSTALLATION
3. Remove the rear seat.
4. Remove the front scuff plates.
5. Remove the rear scuff plates.
6. Remove the console.
7. Remove the front side trims.
8. Remove the B-pillar lower trims.
9. Remove the lower anchor of the front seat belt installation bolts.
10. Remove the tire house trim. (5HB)
11. Remove the fuel-filler lid opener bezel.
12. Remove the fasteners.
13. Remove the cap nuts.
14. Remove the clips.
15. Take the front floor covering off from the passenger-side door opening.
16. Install in the reverse order of removal.
End Of Sie
FLOOR COVERING
A6E7748W001
S–100
SEAT BELT
FRONT SEAT BELT REMOVAL/INSTALLATION
A6E775057630W01
Warning
• Handling the front seat belt (pre-tensioner seat belt) improperly can accidentally deploy the pre-
tensioner, which may seriously injure you. Read SERVICE WARNINGS before handling the front
seat belt. (See
Warning
• The side air bag sensor is attached to the lower part of the B-pillar. When working around the B-
pillar, disconnect the negative battery cable or work carefully, avoiding excessive impact to the
lower part of the B-pillar.
Caution
• The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be
rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the
retractor.
1. Turn the ignition switch to LOCK position.
2. Disconnect the negative battery cable and wait for more than 1 minute.
3. Remove the B-pillar lower trim.
4. Using a screwdriver, pry out the pre-tensioner
seat belt connector's stopper plate.
5. Disconnect the pre-tensioner seat belt connector.
6. Remove the covers.
7. Remove the bolts and screw, then remove the
front seat belt.
8. Install in the reverse order of removal.
9. Verify that the air bag system warning light
illuminates for approximately 6 seconds and
then goes off.
• If the air bag system warning light does not
operate in the manner described above, there
are malfunction in the system. Inspect the
system using the on-board diagnostic
function.
End Of Sie
SEAT BELT
A6E7750W008
A6E7750W007
SEAT BELT
S–101
S
REAR SIDE SEAT BELT REMOVAL/INSTALLATION
A6E775057730W01
Caution
• The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be
rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the
retractor.
4SD
1. Fold the rear seat back.
2. Remove the rear side seats.
3. Remove the rear package trim.
4. Remove the bolts.
5. Remove the rear seat belt.
6. Install in the reverse order of removal.
5HB
Note
• Rear side seat belts are embedded in the rear seat back. See rear seat disassembly/assembly, remove/
install the rear center seat belt.
End Of Sie
REAR CENTER SEAT BELT REMOVAL/INSTALLATION
A6E775057730W02
Caution
• The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be
rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the
retractor.
4SD
1. Fold the rear seat back.
2. Remove the rear package trim.
3. Remove the bolt.
4. Remove the rear center seat belt.
5. Install in the reverse order of removal.
A6E7750W005
A6E7750W003
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст