Mazda 6. Manual — part 286
TRUNK LID
S–39
S
TRUNK LID REMOVAL/INSTALLATION
A6E772052610W01
Warning
• Removing the stay damper without supporting the trunk lid can be dangerous. The trunk lid may
fall and injure you. Open the trunk lid fully and support it before removing the stay damper.
1. Disconnect the negative battery cable.
2. Disconnect the trunk lid harness connector, pull
the trunk lid harness out from the cabin.
3. Disconnect the hooks, which secure the trunk lid
harness to the trunk lid hinge.
4. Pry away the stay damper's band with a
screwdriver.
5. Pry out the connecting part of the stay damper
and the hinge with a screwdriver to disconnect
them. Then remove the stay damper.
TRUNK LID
A6E7720W001
A6E7720W004
A6E7720W002
S–40
TRUNK LID
6. Remove the nuts, then remove the trunk lid.
7. Remove the bolts, then remove the trunk lid
hinge.
8. Install in the reverse order of removal.
9. Adjust the trunk lid. (See
End Of Sie
TRUNK LID DISASSEMBLY/ASSEMBLY
A6E772052610W02
1. Disconnect the negative battery cable.
2. Remove the trunk lid trim.
3. To remove the trunk lid outer handle and trunk lid key cylinder, remove the rear finisher.
4. Disassemble in the order indicated in the table.
5. Assemble in the reverse order of disassembly.
.
End Of Sie
A6E7720W007
A6E7720W006
1
Trunk Lid latch and lock actuator
2
Trunk Lid outer handle
3
Trunk Lid key cylinder
4
Clip
5
Stopper
6
Trunk Lid weatherstrip
7
Trunk Lid
TRUNK LID
S–41
S
TRUNK LID ADJUSTMENT
A6E772052610W03
1. Measure the gap and height between the front door and the body.
2. If not as specified, loosen the door hinge
installation bolts or the door lock striker
installation screws, and reposition the door.
Clearance
a: 2.5—4.5 mm {0.10—0.18 in}
b: -1.0—1.0 mm {-0.04—0.04 in}
c: 4.0—8.0 mm {0.16—0.31 in}
3. Tighten the bolts or screws.
End Of Sie
STAY DAMPER DISPOSAL
A6E772052610W04
Note
• The gas in the stay damper is colorless, odorless, and non-toxic.
1. Wear protective eye wear.
2. Lay the stay damper flat.
3. Saw through the stay damper body using a
hacksaw.
4. Allow the gas to escape from the stay damper.
5. Discard the stay damper.
End Of Sie
A6E7720W005
A6E7722W006
S–42
LIFTGATE
LIFTGATE REMOVAL/INSTALLATION
A6E772262010W01
Warning
• Removing the stay damper without supporting the liftgate can be dangerous. The liftgate may fall
and injure you. Open the liftgate fully and support it before removing the stay damper.
1. Disconnect the negative battery cable.
2. Remove the liftgate lower upper trim.
3. Press the liftgate harness connector's bracket, which is attached to the liftgate, to the (1) direction shown in the
figure, and then detach the fit. Then remove the connector toward the (2) direction shown in the figure.
4. Disconnect the vehicle harness connector and the liftgate connector. Then remove the grommet from the
liftgate.
5. Pry away the stay damper's band with a
screwdriver.
6. Pry out the connecting part of the stay damper
and the hinge with a screwdriver to disconnect
them. Then remove the stay damper.
7. Remove the bolts A, then remove the liftgate.
8. To remove the hinge, remove the headliner and
the nut.
LIFTGATE
A6E7722W003
A6E7722W005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст