Mazda 6. Manual — part 285
POWER DOOR LOCK SYSTEM
S–35
S
*1
: Vehicles with double locking system
*2
: Vehicles with theft-deterrent system
2D
-
-
-
-
-
2E
-
-
-
-
-
2F
Key
reminder
switch
Key reminder switch
Key reminder switch at on
B+
• Inspect key reminder
switch
• Inspect related
harness
Other
Below 1.0
2G
Liftgate
open/closed
Door switch
Lliftgate is open (cargo
compartment light switch is on)
Below 1.0
• Inspect cargo
compartment light
switch
• Inspect related
harness
Liftgate are closed (cargo
compartment light switch are off)
B+
2H
-
-
-
-
-
2I
Hazard
Flasher unit
Except
vehicles
with theft-
deterrent
system
Transmitter LOCK
button is pressed
B+
→Below
1.0
→B+
• Inspect flasher unit
• Inspect related
harness
Transmitter
UNLOCK button is
pressed
B+
→Below
1.0
→B+→Below
1.0
→B+
No transmitter
buttons are pressed
B+
Vehicles
with theft-
deterrent
system
Under any condition
B+
• Inspect theft-
deterrent control
module
• Inspect related
harness
2J
*1
Security
light output
Instrument cluster
Double locking system operated
1.4
• Inspect instrument
cluster
• Inspect related
harness
Other
B+
2K
Door open/
closed
Door switch
Any door is open (any door
switch is on)
Below 1.0
• Inspect door
switches
• Inspect related
harness
All door are closed (door
switches are off)
B+
2L
-
-
-
-
-
2N
-
-
-
-
-
2M
-
-
-
-
-
2O
-
-
-
-
-
2P
*2
Theft-
deterrent
alarm
control
Theft-deterrent
control module
Ignition switch is at ON position
B+
→Below
1.0
→B+
• Inspect theft-
deterrent control
module
• Inspect related
harness
Other
B+
2Q
Lock input
Door lock-link switch
Driver’s side door is locked:
inspect for continuity to ground
Yes
• Inspect door lock-link
switch
• Inspect related
harness
Driver’s side door is unlocked:
inspect for continuity to ground
No
2R
Unlock input Door lock-link switch
Driver’s side door is locked:
inspect for continuity to ground
No
• Inspect door lock-link
switch
• Inspect related
harness
Driver’s side door is unlocked:
inspect for continuity to ground
Yes
2S
Lock/Unlock
input
• Door key cylinder
switch (driver’s
side)
*1
• Door key cylinder
switch
(passenger’s side)
At the moment of key cylinder is
locked
Approx. 2.5
• Inspect key cylinder
switch
• Inspect related
harness
At the moment of key cylinder is
unlocked
Below 1.0
Key cylinder at neutral position
Approx. 5
2T
-
-
-
-
-
2U
-
-
-
-
-
2V
-
-
-
-
-
2W
Signal
ground
GND
Under any condition: inspect for
continuity to ground
Yes
• Inspect GND
2X
-
-
-
-
-
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
S–36
POWER DOOR LOCK SYSTEM
End Of Sie
DOOR LOCK TIMER UNIT ID CODE CHANGE
A6E771801097W01
Note
• When programming the ID code into a door lock timer unit, verify that other transmitters are not being
operated in the vicinity.
End Of Sie
A6E7718W021
POWER DOOR LOCK SYSTEM
S–37
S
TRANSMITTER BATTERY REPLACEMENT
A6E771800110W01
1. Insert a small screwdriver into the slot and gently
pry open the transmitter.
2. Press the portion of the battery indicated by A and
remove the battery.
3. Install a new battery (CR2025) into the front
portion of the holder with the positive pole (+)
facing up. Press on the B portion of the battery to
set the battery.
4. Align the front and back covers and snap the
transmitter shut.
Battery specification
Lithium CR2025
× 1
Note
• The batteries will last about 2 years when
used 10 times a day.
End Of Sie
A6E7718W001
A6E7718W002
A6E7718W003
S–38
POWER DOOR LOCK SYSTEM
TRANSMITTER BATTERY INSPECTION
A6E771800110W02
Caution
• Since the battery voltage does not drop fully if the button is pushed for only 4 seconds or less, it
can not be properly examined to see whether it is good or bad. Always push the button for 5
seconds.
Note
• A correct measurement can not be obtained if the battery temperature is low. Make sure the battery is at
18
°C {64 °F} or more for at least 30 minutes before reinspecting if a measurement value is under the
standard voltage.
1. Remove the transmitter cover.
2. Apply the circuit tester leads to the positions as
indicated in the figure.
3. While pressing the battery as shown in the figure,
press the LOCK and UNLOCK buttons on the
transmitter at the same time to start measurement
of the voltage.
4. Release the buttons after 5 seconds.
5. Verify that the minimum voltage is the standard
voltage or more for 10 seconds after starting
measurement.
• If the voltage is under the standard voltage,
replace the battery.
Standard voltage
2.7 V
End Of Sie
A6E7718W005
A6E7718W006
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст