Mazda CX 7. Manual — part 195
ALL WHEEL DRIVE (AWD)
03-19–11
03-19
End Of Sie
DIFFERENTIAL OIL TEMPERATURE SENSOR REMOVAL/INSTALLATION
id031900800800
Warning
• Hot differential oil may cause severe burns. Do not perform maintenance while differential oil is
hot.
1. Disconnect the negative battery cable.
2. Disconnect the differential oil temperature sensor connector.
3. Remove the differential oil temperature sensor.
4. Apply differential oil to the O-ring.
5. Install the differential oil temperature sensor.
Tightening torque
12.7— 17.3 N·m {1.3— 1.7 kgf·m, 9.4— 12.7
ft·lbf}
6. Connect the differential oil temperature sensor
connector.
7. Connect the negative battery cable.
End Of Sie
WM: 4WD SOLENOID
AWD SOLENOID INSPECTION
id031900800900
1. Disconnect the negative battery cable.
2. Disconnect the AWD solenoid connector.
3. Measure resistance between AWD solenoid
connector terminals A and B.
• If the resistance is not within the specification,
replace the coupling unit.
AWD solenoid resistance
1.5— 2.0 ohms
(Rear differential oil temperature at 20
°C
{68
°F})
4. Connect the AWD solenoid connector.
5. Connect the negative battery cable.
End Of Sie
DIFFERENTIAL OIL
TEMPERATURE SENSOR
acxuuw00001459
A
B
acxuuw00001460
1871-1U-06B(03-19).fm 11 ページ 2006年3月15日 水曜日 午前11時9分
TECHNICAL DATA
03-50–1
03-50
03-50
TECHNICAL DATA
DRIVELINE/AXLE TECHNICAL DATA . . 03-50–1
End of Toc
WM: DRIVELINE/AXLE
DRIVELINE/AXLE TECHNICAL DATA
id035000800100
End Of Sie
Item
Specification
Front wheel bearing maximum play
0.05 mm {0.002 in}
Rear wheel bearing maximum play
0.05 mm {0.002 in}
Front drive shaft length
LH: 658.2—668.2 mm {25.92—26.30 in}
RH: 621.2—631.2 mm {24.46—24.85 in}
Rear drive shaft length
LH: 840.8—850.8 mm {33.11—33.49 in}
RH: 862.3—872.3 mm {33.95—34.34 in}
Rear differential oil
Specified oil grade: API service GL-5
Specified oil viscosity: SAE 80W-90
Capacity (approximate quantity): 1.00 L {1.06 US qt, 0.88 Imp qt}
Rear differential backlash of pinion gear and side gear
0.1 mm {0.004 in} or less
Rear differential pinion height
–0.032—0.032 mm {–0.0012—0.0012 in}
Rear differential drive pinion preload
1.3—1.8 N·m {13.3—18.2 kgf·cm, 11.5—15.9 in·lbf}
Rear differential backlash of drive pinion and ring gear
Standard: 0.09—0.11 mm {0.003—0.004 in}
Minimum value: 0.05 mm {0.002 in}
Propeller shaft maximum runout
0.8 mm {0.031 in}
Propeller shaft starting torque
0.29—1.47 N·m {3.0—14.9 kgf·cm, 2.6—13.0 in·lbf}
Transfer oil
Specified oil grade: API Service GL-5
Specified oil viscosity: SAE 80W-90
Capacity (approximate quantity): 1.2 L {1.3 US qt, 1.1 lmp qt}
1871-1U-06B(03-50).fm 1 ページ 2006年3月15日 水曜日 午前11時10分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст