Mazda CX 7. Manual — part 421
LIGHTING SYSTEMS
09-18–19
09-18
AUTO LIGHT SENSOR REMOVAL/INSTALLATION
id091800807200
1. Disconnect the negative battery cable.
2. Remove the dashboard under cover (RH).
3. Push out the auto light sensor with connector from under the instrument panel.
4. Remove in the order indicated in the table.
.
5. Install in the reverse order of removal.
End Of Sie
AUTO LIGHT SENSOR INSPECTION
id091800807600
Note
• Inspect the auto light sensor from the back side of the connector with the connector still connected.
1. Measure the voltage at auto light sensor terminal A and verify that the voltage is 5 V.
2. Shine a fluorescent light or expose the auto light sensor to natural sunlight.
3. Connect the positive (+) lead to terminal B and
the negative (
−) lead to terminal C of the auto light
sensor, and verify that the voltages are as shown
in the table.
• If the voltage is not as specified, replace the
auto light sensor.
End Of Sie
AUTO LIGHT CONTROL MODULE REMOVAL/INSTALLATION
id091800807300
1. Disconnect the negative battery cable.
2. Remove the meter hood. (See 09-17-10 METER HOOD REMOVAL/INSTALLATION.)
3. Remove the instrument cluster. (See 09-22-2 INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
End Of Sie
1
Connector
2
Auto light sensor
1
2
acxuuw00001753
A
B
C
acxuuw00002401
Voltage (V)
Test condition
: Continuity
Sensor subject to fluorescent
light or natural sunlight
Sensor covered by a cloth
0.21
—
4.65
0.20 or less
acxuuw00002542
1
Screw
2
Connector
3
Auto light control module
3
1
2
acxuuw00001754
LIGHTING SYSTEMS
09-18–20
AUTO LIGHT CONTROL MODULE INSPECTION
id091800807400
1. Measure the voltage at the auto light control module terminals as indicated below.
2. Disconnect the auto light control module connector before inspecting for continuity at terminals 1K, 2A, 2O and
2P.
• If not as specified, inspect the parts listed under “Action.”
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the auto light
control module.
Terminal Voltage List (Reference)
Terminal
Signal
Connection
Test condition
Voltage (V)/
Continuity
Action
1A*
Power supply
DRL 15 A fuse
Constant
B+
• Inspect DRL 15 A
fuse
• Inspect related
harness
1D*
Headlight (LH)
operation
(high-beam)
Headlight (LH)
(high-beam)
Light switch at
headlight
position
Dimmer switch at
the high-beam
position
B+
• Inspect headlight
(LH)
• Inspect related
harness
Dimmer switch at
the low-beam
position
1.0 or less
1G*
Headlight (LH)
operation
(high-beam)
Headlight (LH)
(high-beam)
Light switch at
headlight
position
Dimmer switch at
the high-beam
position
1.0 or less
• Inspect headlight
(LH)
• Inspect related
harness
DRL mode
B+
1H*
Headlight (RH)
operation
(high-beam)
Headlight (RH)
(high-beam)
Light switch at
headlight
position
Dimmer switch at
the high-beam
position
B+
• Inspect headlight
(RH)
• Inspect related
harness
Dimmer switch at
the low-beam
position
1.0 or less
1K*
Ground
GND
Constant: check for continuity to
ground
Yes
Inspect GND
2A
Ground
GND
Constant: check for continuity to
ground
Yes
Inspect GND
2B
Auto light
sensor input
Auto light sensor
fluorescent light shined directly on the
auto light sensor
0.21—4.65
• Inspect auto light
sensor
• Inspect related
harness
Blocking light to auto light sensor
0.20 or less
• Inspect auto light
sensor
• Inspect related
harness
2C
IG1
METER 10 A
fuse
Ignition switch at ON
B+
• Inspect METER 10 A
fuse
• Inspect related
harness
Ignition switch at LOCK or ACC
1.0 or less
2B
*
2A
2C
2G
2H
2I
2K
2L
2M
2N
2O
2P
*
*
1A
1K
1D
AUTO LIGHT CONTROL MODULE
HARNESS SIDE CONNECTOR
*
1G
*
*
*
1H
*
*
*
2J
acxuuw00001826
LIGHTING SYSTEMS
09-18–21
09-18
*
: For vehicles with DRL only.
End Of Sie
2G
Power supply
ROOM 15 A
fuse
Constant
B+
• Inspect ROOM 15 A
fuse
• Inspect related
harness
2H
Auto light
sensor power
supply
Auto light sensor Constant
5
• Inspect auto light
sensor
• Inspect related
harness
2I*
Front fog light
relay on/off
Front fog light
relay
Light switch at
headlight
position and
dimmer switch at
LO
Front fog light
switch at ON
2.0 or less
• Inspect front fog light
relay
• Inspect related
harness
Front fog light
switch at OFF
B+
2J*
Front fog light
switch on/off
Front fog light
switch
Light switch at
headlight
position and
dimmer switch at
LO
Front fog light
switch at ON
1.0 or less
• Inspect light switch
• Inspect related
harness
Front fog light
switch at OFF
B+
2K*
High-beam on/
off
Light switch
Light switch at
headlight
position
Dimmer switch at
HI
1.0 or less
• Inspect light switch
• Inspect related
harness
Dimmer switch at
LO
B+
2L
Light switch
(Auto) signal
Light switch
Ignition switch at
ON
Light switch at
AUTO position
1.0 or less
• Inspect light switch
• Inspect related
harness
Other
B+
2M
TNS relay
operation/TNS
switch on/off
TNS relay
Ignition switch at
ON and light
switch at AUTO
position
Parking lights turn
on (Sensor voltage
is 0.3 V or less.)
1.0 or less
• Inspect TNS 15 A
fuse
• Inspect TNS relay
• Inspect related
harness
Parking lights turn
off (Sensor voltage
is 2.3 V or more.)
B+
Light switch
Ignition switch at
ON
Light switch at TNS
or headlight
position
1.0 or less
• Inspect light switch
• Inspect related
harness
Light switch at OFF
position
B+
2N
Headlight relay
operation/
headlight
switch on/off
Headlight relay
Ignition switch at
ON and light
switch at AUTO
position
Headlights (low-
beam) turn on
(Sensor voltage is
0.3 V or less.)
1.0 or less
• Inspect headlight
relay
• Inspect related
harness
Headlights (low-
beam) turn off
(Sensor voltage is
2.3 V or more.)
B+
Light switch
Light switch at headlight position
1.0 or less
• Inspect light switch
• Inspect related
harness
Light switch at OFF or TNS position
B+
2O
Ground
GND
Constant: check for continuity to
ground
Yes
Inspect GND
2P*
Parking brake
lever
depressed/
released
Parking brake
switch
Parking brake lever depressed: check
for continuity to ground
Yes
• Inspect parking
brake switch
• Inspect related
harness
Parking brake lever released: check
for continuity to ground
No
Terminal
Signal
Connection
Test condition
Voltage (V)/
Continuity
Action
LIGHTING SYSTEMS
09-18–22
AUTO LIGHT ILLUMINATION LEVEL SETTING
id091800803300
Caution
• If any of the following occurs, the sensitivity cannot be set properly. Therefore, resume from Step
1.
• Each procedure and operation interval exceeds 5 s.
• Procedures are performed incorrectly.
Note
• Perform the procedure in a condition that allows verification of the headlight illumination because it is
necessary to verify the setting condition according to the number of times headlights turn on.
1. Turn the ignition switch to the ON position with the light switch in the OFF position and pulled back (Flash-to-
pass ON).
2. Switch the light switch from the OFF to TNS position five times and return it to the OFF position.
3. Pull the light switch back once. (Flash-to-pass ON)
4. Turn the light switch to the TNS position.
5. Switch the light switch from the TNS to ON position five times and return it to the TNS position.
6. Turn the light switch to the ON position.
7. Switch the light switch from the ON to AUTO position five times and return it to the ON position.
8. Turn the light switch to the TNS position.
Note
• Switches to the sensitivity setting mode when the above operations are performed.
• The headlights turn on for the number of times according to the current setting conditions.
— Illumination (Two times): Standard sensitivity
— Illumination (Three times): Low sensitivity
9. Switch the sensitivity by pulling the light switch back (Flash-to pass ON).
10. Verify the number of times the headlights turn on and that the sensitivity is set properly.
• Illumination (Two times): Standard sensitivity
• Illumination (Three times): Low sensitivity
End Of Sie
WM: INTERIOR LIGHT
MAP LIGHT REMOVAL/INSTALLATION
id091800801200
1. Disconnect the negative battery cable.
2. Insert a scraper into the gap between the headliner and the map light.
3. Press the tab and remove the map light.
4. Disconnect the connector.
5. Remove the socket, then remove the map light
bulb.
6. Install in the reverse order of removal.
End Of Sie
TAB
acxuuw00001759
MAP LIGHT
MAP
LIGHT
BULB
SOCKET
CONNECTOR
MAP LIGHT
BULB
SOCKET
CONNECTOR
acxuuw00001760
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст