Mazda CX 7. Manual — part 422
LIGHTING SYSTEMS
09-18–23
09-18
MAP LIGHT INSPECTION
id091800801300
1. Verify that the continuity between the map light
terminals is as indicated in the table.
• If not as indicated in the table, replace the
map light.
End Of Sie
INTERIOR LIGHT BULB REMOVAL/INSTALLATION
id091800801400
1. Disconnect the negative battery cable.
2. Insert a tape-wrapped flathead screwdriver into
the service hole and pry with the screwdriver in
the direction shown by the arrow to remove the
lens.
3. Remove the interior light bulb.
4. Install in the reverse order of removal.
End Of Sie
INTERIOR LIGHT REMOVAL/INSTALLATION
id091800801500
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) A-pillar lower trim (See 09-17-16 A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(2) A-pillar trim (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(3) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(4) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(5) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(6) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(7) B-pillar upper trim (See 09-17-16 B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
(8) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(9) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(10)Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(11)Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
C
B
A
B
C
DOOR
OFF
MAP LIGHT
SWITCH (LH)
INTERIOR LIGHT
SWITCH
MAP LIGHT
SWITCH (RH)
*
A
EPU918ZW3017
-
B
C
A
-
:
Bulb
Terminal
Switch position
INTERIOR
LIGHT
SWITCH
MAP
LIGHT
SWITCH
ON
OFF
DOOR
OFF
EPU918ZW3018
SERVICE HOLE
acxuuw00001761
INTERIOR LIGHT
INTERIOR LIGHT
BULB
acxuuw00001762
LIGHTING SYSTEMS
09-18–24
(12)C-pillar trim (See 09-17-17 C-PILLAR TRIM REMOVAL/INSTALLATION.)
(13)D-pillar trim (See 09-17-18 D-PILLAR TRIM REMOVAL/INSTALLATION.)
(14)Map light (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
(15)Sunvisor (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
(16)Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
(17)Headliner (See09-17-27 HEADLINER REMOVAL/INSTALLATION.)
3. Detach the tab and remove the interior light.
4. Install in the reverse order of removal.
End Of Sie
INTERIOR LIGHT INSPECTION
id091800801600
1. Verify that the continuity between the interior light
terminals is as indicated in the table.
• If not as indicated in the table, replace the
interior light.
End Of Sie
WM: CARGO COMPARTMENT LIGHT
CARGO COMPARTMENT LIGHT BULB REMOVAL/INSTALLATION
id091800807800
1. Disconnect the negative battery cable.
2. Insert a tape-wrapped flathead screwdriver into
the service hole and pry with the screwdriver in
the direction shown by the arrow to remove the
lens.
INTERIOR LIGHT
CONNECTOR
TAB
acxuuw00002409
OFF
DOOR
ON
D
B
C
B
C
D
INTERIOR LIGHT
SWITCH
*
acxuuw00001766
D
C
B
ON
DOOR
OFF
:
Bulb
Switch position
Terminal
acxuuw00001767
SERVICE HOLE
acxuuw00002412
LIGHTING SYSTEMS
09-18–25
09-18
3. Remove the cargo compartment light bulb.
4. Install in the reverse order of removal.
End Of Sie
CARGO COMPARTMENT LIGHT REMOVAL/INSTALLATION
id091800801700
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) A-pillar lower trim (See 09-17-16 A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(2) A-pillar trim (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(3) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(4) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(5) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(6) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(7) B-pillar upper trim (See 09-17-16 B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
(8) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(9) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(10)Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(11)Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
(12)C-pillar trim (See 09-17-17 C-PILLAR TRIM REMOVAL/INSTALLATION.)
(13)D-pillar trim (See 09-17-18 D-PILLAR TRIM REMOVAL/INSTALLATION.)
(14)Map light (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
(15)Sunvisor (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
(16)Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
(17)Headliner (See09-17-27 HEADLINER REMOVAL/INSTALLATION.)
3. Detach the tab and remove the interior light..
4. Install in the reverse order of removal.
End Of Sie
CARGO COMPARTMENT LIGHT INSPECTION
id091800801800
1. Verify that the continuity between the cargo
compartment light terminals is as indicated in the
table.
• If not as indicated in the table, replace the
cargo compartment light.
End Of Sie
WM: IGNITION KEY ILLUMINATION
CARGO
COMPARTMENT
LIGHT
CARGO
COMPARTMENT
LIGHT BULB
acxuuw00002413
CARGO
COMPARTMENT
LIGHT
CONNECTOR
TAB A
A
TAB A
A
A
A
acxuuw00002410
D
C
OFF
ON
D
C
*
*
acxuuw00001771
: Bulb
Switch position
ON
OFF
Terminal
D
C
acxuuw00002414
LIGHTING SYSTEMS
09-18–26
IGNITION KEY ILLUMINATION BULB REMOVAL/INSTALLATION
id091800802400
1. Disconnect the negative battery cable.
2. Remove the lower column cover. (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove the ignition key illumination bulb.
4. Install in the reverse order of removal.
End Of Sie
WM: ENTERTAINMENT ILLUMINATION
SPOT LIGHT REMOVAL/INSTALLATION
id091800807500
1. Disconnect the negative battery cable.
2. Remove the A-pillar trim. (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
3. Remove the sunvisor. (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
4. Remove the map light. (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
5. Set the headliner out of the way.
6. Remove in the order indicated in the table.
.
7. Install in the reverse order of removal.
End Of Sie
WM: DOOR SWITCH
DOOR SWITCH REMOVAL/INSTALLATION
id091800803400
1. Disconnect the negative battery cable.
2. Disassemble in the order indicated in the table.
.
3. Install in the reverse order of removal.
End Of Sie
IGNITION KEY
ILLUMINATION BULB
acxuuw00001773
1
Connector
2
Spot light
3
Cover A
4
Cover B
5
Lens
3
5
4
1
2
TAB
TAB
acxuuw00002277
1
Screw
2
Door switch
3
Connector
3
1
2
acxuuw00001774
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст