Mazda CX 7. Manual — part 325
SEAT BELT
08-11–5
08-11
4. While pulling the seat belt out, make sure that the
seat belt does not lock when the retractor is tilted
slowly up to 15
° from the mounted position and
locks when the retractor is tilted 40
° or more.
• If there is any malfunction, replace the seat
belt.
ALR
1. Pull the belt out fully to change the lock mode from ELR to ALR.
2. Verify that retractor makes a clicking sound as the belt slowly retracts. If no sound is heard, the lock mode has
not changed to ALR. If necessary, repeat Step 1.
• If there is any malfunction, replace the seat belt.
3. Verify that the retractor locks when pulled.
• If there is any malfunction, replace the seat belt.
4. Verify that the lock mode changes to ELR when the belt is fully pulled out.
• If there is any malfunction, replace the seat belt.
Load Limiter Retractor
Warning
• When the load limiter operates, the belt and anchor rub against each other strongly leaving wear
tracks. If the seat belt is used in this state, the seat belt will not function at its full capability and
there is the possibility of serious injury to passengers. Be sure to replace the seat belt once the
load limiter operates.
1. If the vehicle has been subjected to a shock in an
accident, pull the belt from the retractor and
confirm that there are no wear tracks (the load
limiter has not operated) by visually inspecting
and feeling the belt.
• If there is any malfunction, replace the seat
belt.
End Of Sie
WM: FRONT BUCKLE
FRONT BUCKLE REMOVAL/INSTALLATION
id081100800400
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable.
3. Remove the front seat. (See 09-13-2 FRONT SEAT REMOVAL/INSTALLATION.)
4. Detach the tab as shown in the figure and remove
the connector from the front seat connector.
RETRACTOR
acxuuw00002084
ANCHOR
TRACE
OF WEAR
BELT
PULL
acxuuw00002085
FRONT SEAT
CONNECTOR
FRONT BUCKLE
CONNECTOR
TAB
acxuuw00001028
1871-1U-06B(08-11).fm 5 ページ 2006年3月15日 水曜日 午前11時37分
SEAT BELT
08-11–6
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
End Of Sie
WM: REAR BUCKLE
REAR BUCKLE REMOVAL/INSTALLATION
id081100800700
1. Remove the rear seat cushion. (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
WM: FRONT BUCKLE
BUCKLE SWITCH INSPECTION
id081100803000
1. Inspect for continuity between the buckle switch
terminals using a tester.
• If not as indicated in the table, replace the
front buckle.
End Of Sie
WM: CHILD-RESTRANT SEAT ANCHOR
CHILD-RESTRAINT SEAT ANCHOR REMOVAL/INSTALLATION
id081100800100
1. Remove the trunk end trim bezel.
2. Remove in the order indicated in the table.
.
3. Install in the reverse order of removal.
End Of Sie
1
Bolt
2
Front buckle
2
1
40.0—50.0 N·m
{4.08—5.09 kgf·m,
29.5—36.8 ft·lbf}
acxuuw00001029
1
Bolt
2
Rear buckle
N·m {kgf·m, ft·lbf}
38.3—78.4
{3.90—7.99,
28.3—57.8}
1
2
acxuuw00001030
A
B
A
B
acxuuw00002101
: Continuity
Seat belt
Fastened
Unfastened
Terminal
B
A
acxuuw00002102
1
Bolt
2
Child-restraint seat anchor
1
2
18.0—27.0 N·m
{1.84—2.75 kgf·m,
13.3—19.9 ft·lbf}
acxuuw00001025
1871-1U-06B(08-11).fm 6 ページ 2006年3月15日 水曜日 午前11時37分
SERVICE TOOLS
08-60–1
08-60
08-60
SERVICE TOOLS
RESTRAINTS SST . . . . . . . . . . . . . . . . . 08-60–1
End of Toc
WM: RESTRAINTS
RESTRAINTS SST
id086000800100
End Of Sie
49 H066 002
Deployment
tool
49 B066 004
Adapter
harness
49 L066 002
Adapter
harness
49 G066 003
Adapter
harness
49 N088 0A0
Fuel and
Thermometer
checker
-
1871-1U-06B(08-60).fm 1 ページ 2006年3月15日 水曜日 午前11時38分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст