Mazda CX 7. Manual — part 412
INTERIOR TRIM
09-17–15
09-17
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
Revised 3/2007 (Ref. No. R038/07)
CONSOLE PANEL REMOVAL/INSTALLATION
id091700804100
1. Detach clips A from the console using a tape-
wrapped flathead screwdriver.
2. Remove the pin B and tab C.
3. Remove the pin D.
4. Remove the console panel.
5. Install in the reverse order of removal.
End Of Sie
WM: PILLAR TRIM
A-PILLAR TRIM REMOVAL/INSTALLATION
id091700801900
1. Partially peel back the seaming welt.
2. Pull the A-pillar trim shown in the figure in the
direction of the arrow, raise clip B from its
grommet together with the A-pillar trim, and
remove clips A at the same time.
3. Slide the A-pillar trim in the direction of the arrow
shown in the figure and remove the A-pillar trim
from clip B.
CONSOLE PANEL
CLIP A
PIN B
PIN D
TAB C
A
A
A
A
A
C
D
B
acxuuw00000865
CLIP A
CLIP B
GROMMET
A-PILLAR TRIM
(INSIDE VIEW)
R
R
TAB
A-PILLAR TRIM
A
B
A
acxuuw00002600
A-PILLAR TRIM
A-PILLAR TRIM
(INSIDE VIEW)
CLIP B
R
acxuuw00002601
INTERIOR TRIM
09-17–16
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
Revised 3/2007 (Ref. No. R038/07)
4. Rotate and pull clip B in the direction of the arrow
shown in the figure until it is no longer loose, and
feels tight.
5. Pull clip B and remove it from the grommet.
6. Insert a tape-wrapped flathead screwdriver
between the body and the grommet.
7. Press the tabs and remove the grommet.
8. Install the new grommet to the body.
9. Install the new clip B to the A-pillar trim.
10. Install the A-pillar trim.
End Of Sie
A-PILLAR LOWER TRIM REMOVAL/INSTALLATION
id091700804400
1. Pull the A-pillar lower trim upward and detach
clips A from the dashboard.
2. Pull the A-pillar lower trim outward and detach
clips B and tab C.
3. Remove the A-pillar lower trim.
4. Install in the reverse order of removal.
End Of Sie
B-PILLAR LOWER TRIM REMOVAL/INSTALLATION
id091700802000
1. Remove the front scuff plate inner. (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
2. Remove the rear scuff plate inner. (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
3. Partially peel back the seaming welt.
4. Pull the B-pillar lower trim outward and detach
clips A, C and locator pins B.
5. Remove the B-pillar lower trim.
6. Install in the reverse order of removal.
End Of Sie
R
CLIP B
R
GROMMET
ac9uuw00002635
GROMMENT
R
TAB
acxuuw00002591
CLIP A.B
A
A
B
B
C
TAB C
A-PILLAR LOWER TRIM
acxuuw00000924
A
A
FRONT
CLIP C
CLIP A
CLIP C DETAIL
LOCATOR PIN B
B
B
B
C
C
C
B-PILLAR LOWER
TRIM
acxuuw00000679
INTERIOR TRIM
09-17-16–1
09-17
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
09-17-16
INTERIOR TRIM
B-PILLAR UPPER TRIM REMOVAL/INSTALLATION
id091700802100
1. Remove the following parts:
(1) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(2) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(3) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(4) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
2. Partially peel back the seaming welt.
3. Remove the screw.
4. Pull the B-pillar upper trim outward and detach
clip A and locator pin B.
5. Pull the B-pillar upper trim downward and detach
the tabs and clip C.
6. Remove the B-pillar upper trim.
End Of Sie
B
A
C
SEAMING WELT
CLIP C
CLIP A
TAB
B-PILLAR UPPER
TRIM
FRONT
SCREW
LOCATOR PIN B
acxuuw00000680
INTERIOR TRIM
09-17-16–2
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
THIS PAGE INTENTIONALLY
LEFT BLANK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст