Mazda Protege 5. Manual — part 299
AIR BAG SYSTEM
08–10–22
11. Press the activation switch on the SST
(Deployment tool) to deploy the side air bag
module.
Pre-tensioner seat belt
1. Remove the pre-tensioner seat belt.
2. Connect the SST (49 D066 003) to the pre-
tensioner seat belt as shown in the figure.
Warning
••••
If the pre-tensioner seat belt is not
properly installed to the tire, serious
injury may occur when the pre-tensioner
part is deployed. When installing the pre-
tensioner seat belt to the tire, make sure
the pre-tensioner part is inside the tire.
3. With the pre-tensioner part inside the tire, tie the
pre-tensioner seat belt to the tire. Wrap the wire
harness through the tire and around the pre-
tensioner seat belt at least four times.
4. Stack the tire with the pre-tensioner seat belt on
top of two tires. Stack a tire on top of the three
tires. Stack another tire that has a wheel on top of
the four tires.
Y3U810WAM
Z3U0810W005
Z3U0810W006
YLE8130W201
1712-1U-01G(08-10).fm 22 ページ 2001年6月29日 金曜日 午前10時24分
AIR BAG SYSTEM
08–10–23
08–10
5. Tie all tires together with wire.
6. Connect the SST (49 H066 002) to the SST (49
D066 003).
7. Connect the red clip of the SST (49 H066 002) to
the positive battery terminal and the black clip to
the negative battery terminal.
8. Verify that the red light on the SST (49 H066 002)
is illuminated.
9. Make sure all persons are standing at least 6 m
{20 ft} from the vehicle.
10. Press the activation switch on the SST (49 H066
002) to deploy the pre-tensioner seat belt.
End Of Sie
AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DISPOSAL PROCEDURES
A3U081057000W03
Warning
••••
Before scrapping a vehicle with a live (undeployed) air bag module and pre-tensioner seat belt,
deploy the air bag module. Never dispose of a live (undeployed) air bag module and pre-tensioner
seat belt.
••••
The air bag module and pre-tensioner seat belt are very hot immediately after it is deployed. You
can get burned. Do not touch the air bag module and pre-tensioner seat belt for at least 15 minutes
after deployment.
••••
Pouring water on the deployed air bag module and pre-tensioner seat belt are dangerous. The
water will mix with the residual gases to form a gas that can make breathing difficult. Do not pour
water on the deployed air bag module and pre-tensioner seat belt.
••••
The deployed air bag module and pre-tensioner seat belt may contain deposits of sodium
hydroxide, a caustic by product of the gas-generated combustion. If this substance gets into your
eyes or on your hands, it can cause irritation and itching. When handling the deployed air bag
module and pre-tensioner seat belt, wear gloves and safety glasses.
1. Put on gloves and safety glasses.
2. Put the deployed air bag module or pre-tensioner seat belt in a plastic bag, seal it, and then dispose of it.
3. Wash your hands after removing your gloves.
End Of Sie
XME8126W008
XME8126W009
XME8126W010
1712-1U-01G(08-10).fm 23 ページ 2001年6月29日 金曜日 午前10時24分
AIR BAG SYSTEM
08–10–24
INSPECTION OF SST (DEPLOYMENT TOOL)
A3U081001078W01
•
Use the SST (Deployment tool) to deploy a live
(undeployed) air bag module before disposing of
it.
•
Before using the SST (Deployment tool), inspect
its operation.
Inspection Procedure
1. Follow the steps below to verify that the SST (Deployment tool) is operating correctly.
•
If not as specified, do not use the SST (Deployment tool) because it may cause the air bag module to
unexpectedly deploy upon connection to the air bag module.
End Of Sie
X3U810WB7
Step
Inspection procedure
Light condition
Green
Red
1
Connect red clip to positive
battery terminal and black clip
to negative battery terminal.
On
Off
2
Connect connectors A and B
of SST (Deployment tool).
Off
On
3
Press activation switch.
On
Off
X3U810WB8
1712-1U-01G(08-10).fm 24 ページ 2001年6月29日 金曜日 午前10時24分
SEAT BELT
08–11–1
08–11
08–11
SEAT BELT
FRONT SEAT BELT
REMOVAL/INSTALLATION . . . . . . . . . 08–11–1
REAR SEAT BELT
REMOVAL/INSTALLATION . . . . . . . . . 08–11–1
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–2
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–2
REAR CENTER SEAT BELT
REMOVAL/INSTALLATION . . . . . . . . . 08–11–3
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–3
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–3
FRONT BUCKLE
REMOVAL/INSTALLATION . . . . . . . . . 08–11–3
REAR BUCKLE
REMOVAL/INSTALLATION . . . . . . . . . . 08–11–4
SEAT BELT INSPECTION . . . . . . . . . . . . 08–11–4
Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–4
ELR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–4
ALR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08–11–4
BUCKLE SWITCH INSPECTION . . . . . . . 08–11–5
CHILD RESTRAINT SEAT ANCHOR
REMOVAL/INSTALLATION . . . . . . . . . . 08–11–5
ISOFIX Anchor . . . . . . . . . . . . . . . . . . . 08–11–5
Tether Anchor . . . . . . . . . . . . . . . . . . . . 08–11–5
End of Toc
FRONT SEAT BELT REMOVAL/INSTALLATION
A3U081157630W01
Warning
••••
Handling the front seat belt (pre-tensioner seat belt) or the side air bag sensor improperly can
accidentally deploy the pre-tensioner or the side air bag module, which may seriously injure you.
Read SERVICE WARNINGS before handling the front seat belt or working around the B-pillar
areas. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)
Note
•
The side air bag sensor is located in the B-pillar.
Caution
••••
The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be
rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the
retractor.
1. Disconnect the negative battery cable.
2. Remove the B-pillar lower trim. (See 09–17–10 B-PILLAR LOWER TRIM REMOVAL.) (See 09–17–11 B-
PILLAR LOWER TRIM INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
1
Anchor cover
2
Front seat belt
X3U811WA0
1712-1U-01G(08-11).fm 1 ページ 2001年6月29日 金曜日 午前10時25分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст