Mazda Protege 5. Manual — part 310
DOORS AND LIFTGATE
09–11–4
REAR DOOR ADJUSTMENT
A3U091172010W01
1. Measure the gap and height between the rear
door and the body.
•
If not as specified, loosen the door hinge
installation bolts or the door lock striker
installation screws, and reposition the door.
(See 09–11–4 REAR DOOR REMOVAL/
INSTALLATION.) (See 09–14–7 DOOR
LOCK STRIKER REMOVAL/
INSTALLATION.)
Clearance
a: 3.5—5.5 mm {0.14—0.21 in}
b: –1.0—0.5 mm {–0.040—0.019 in}
c: 3.0—5.0 mm {0.12—0.19 in}
d: –1.0—1.0 mm {–0.040—0.039 in}
2. Tighten the bolts or screws.
End Of Sie
REAR DOOR REMOVAL/INSTALLATION
A3U091172010W02
Warning
••••
Handling the side air bag sensor improperly can accidentally deploy the side air bag module,
which may seriously injure you. Read AIR BAG SYSTEM SERVICE WARNINGS before working
around the B-pillar areas. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)
Note
•
The side air bag sensor is located in the B-pillar.
1. Disconnect the negative battery cable.
2. To remove the checker, turn the door screen over.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Adjust the rear door. (See 09–11–4 REAR DOOR
ADJUSTMENT.)
Z3U0911W004
1
Connector
(See 09–11–5 Connector Removal Note)
(See 09–11–5 Connector Installation Note)
2
Checker pin
3
Rear door hinge
4
Rear door
5
Checker
Z3U0911W003
1712-1U-01G(09-11).fm 4 ページ 2001年6月29日 金曜日 午後12時7分
DOORS AND LIFTGATE
09–11–5
09–11
Connector Removal Note
1. Pull the pin outward.
2. Disconnect the connector.
Connector Installation Note
1. Push the pin in.
2. Connect the connector.
3. Push the pin in again.
End Of Sie
REAR DOOR DISASSEMBLY/ASSEMBLY
A3U091172010W03
1. Open the rear door glass completely.
2. Disconnect the negative battery cable.
3. Remove the rear door trim. (See 09–17–9 REAR DOOR TRIM REMOVAL/INSTALLATION.)
4. Disassemble in the order indicated in the table.
X3U911WA6
1712-1U-01G(09-11).fm 5 ページ 2001年6月29日 金曜日 午後12時7分
DOORS AND LIFTGATE
09–11–6
5. Assemble in the reverse order of disassembly.
.
End Of Sie
X3U911WA7
1
Inner handle
2
Door lock knob
3
Door screen
4
Glass guide
5
Door quarter window glass weatherstrip
6
Door quarter window glass
7
Rear door glass
8
Rear power window regulator
9
Glass run channel
10
Rear manual window regulator
11
Rear door lock
12
Outer handle
13
Door weatherstrip
1712-1U-01G(09-11).fm 6 ページ 2001年6月29日 金曜日 午後12時7分
DOORS AND LIFTGATE
09–11–7
09–11
LIFTGATE REMOVAL/INSTALLATION
A3U091162010W01
Warning
••••
Removing the stay damper without supporting the liftgate can be dangerous. The liftgate may fall
and injure you. Open the liftgate fully and support it before removing the stay damper.
1. Disconnect the negative battery cable.
2. Remove the headliner. (See 09–17–16 HEADLINER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Adjust the liftgate. (See09–11–9 LIFTGATE
ADJUSTMENT)
End Of Sie
1
Connector
2
Rear washer hose
3
Bolt
4
Nut
5
Liftgate
A3U0911W001
1712-1U-01G(09-11).fm 7 ページ 2001年6月29日 金曜日 午後12時7分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст