Mazda Protege 5. Manual — part 332
EXTERIOR TRIM
09–16–7
09–16
Rear Carrier Bar Installation Note
1. Loosen the bolt under the rear carrier bar, and
adjust the rear carrier bar position.
2. When the rear carrier bar is in the final position,
align the square hole line for cover B with the rear
cover line.
End Of Sie
FRONT BELTLINE MOLDING REMOVAL/INSTALLATION
A3U091650640W01
1. Open the front door glass fully.
2. Remove the screw.
3. Pull the front beltline molding up, then remove it.
4. Install in the reverse order of removal.
End Of Sie
REAR BELTLINE MOLDING REMOVAL/INSTALLATION
A3U091650660W01
1. Remove the rear door glass. (See 09–11–5 REAR DOOR DISASSEMBLY/ASSEMBLY.)
2. Remove the screw.
3. Pull the rear beltline molding up, then disengage
clip A.
4. Install in the reverse order of removal.
End Of Sie
REAR WINDOW GLASS MOLDING REMOVAL
A3U091650690W01
Note
•
Rear window glass molding is a replacement part.
1. Remove the rear window glass. (See 09–12–11 REAR WINDOW GLASS REMOVAL.)
2. Remove the rear window glass molding from the rear window glass.
End Of Sie
REAR WINDOW GLASS MOLDING INSTALLATION
A3U091650690W02
Note
•
Rear window glass molding is a replacement part.
1. Install the rear window glass molding to the rear window glass. (See 09–12–14 REAR WINDOW GLASS
INSTALLATION.)
End Of Sie
A3U0916W012
X3U916WA9
X3U916WAA
1712-1U-01G(09-16).fm 7 ページ 2001年6月29日 金曜日 午前10時34分
EXTERIOR TRIM
09–16–8
WINDSHIELD MOLDING REMOVAL
A3U091650600W01
Note
•
Windshield molding is a replacement part.
1. Remove the windshield. (See 09–12–19 WINDSHIELD REMOVAL.)
2. Remove the windshield molding from the windshield.
End Of Sie
WINDSHIELD MOLDING INSTALLATION
A3U091650600W02
Note
•
Windshield molding is a replacement part.
1. Install the windshield molding to the windshield. (See 09–12–21 WINDSHIELD INSTALLATION.)
End Of Sie
ROOF MOLDING REMOVAL/INSTALLATION
A3U091650620W01
1. Pull the front edge and rear edge of the roof
molding up (1).
2. Slide the roof molding rearward, then remove it
(2).
3. Install in the reverse order of removal.
End Of Sie
REAR SPOILER REMOVAL/INSTALLATION
A3U091651950W01
4SD
1. Disconnect the negative battery cable.
2. Disconnect the high-mount brake light connector.
3. Remove the bolts.
4. Pull the rear spoiler upward, then remove it.
5. Install in the reverse order of removal.
X3U916WAB
Y3U916WA0
1712-1U-01G(09-16).fm 8 ページ 2001年6月29日 金曜日 午前10時34分
EXTERIOR TRIM
09–16–9
09–16
5HB
1. Disconnect the negative battery cable.
2. Remove the hole cover A using a tape-wrapped screwdriver.
3. Remove the fasteners, then remove hole cover B.
4. Pull out the high-mount brake light connector,
then disconnect it.
5. Remove the bolts and nuts.
6. Pull the rear spoiler upward, then disengage clips
A from the body.
7. Install in the reverse order of removal.
End Of Sie
A3U0916W006
A3U0916W007
1712-1U-01G(09-16).fm 9 ページ 2001年6月29日 金曜日 午前10時34分
INTERIOR TRIM
09–17–1
09–17
09–17
INTERIOR TRIM
DASHBOARD
REMOVAL/INSTALLATION . . . . . . . . . 09–17–1
DASHBOARD
DISASSEMBLY/ASSEMBLY . . . . . . . . 09–17–3
VENTILATOR GRILLE
REMOVAL/INSTALLATION . . . . . . . . . 09–17–3
Center Side . . . . . . . . . . . . . . . . . . . . . 09–17–3
Driver’s side . . . . . . . . . . . . . . . . . . . . . 09–17–4
Passenger’s side . . . . . . . . . . . . . . . . . 09–17–4
CENTER PANEL
REMOVAL/INSTALLATION . . . . . . . . . 09–17–4
COLUMN COVER
REMOVAL/INSTALLATION . . . . . . . . . 09–17–5
CONSOLE ADJUSTMENT . . . . . . . . . . . 09–17–5
CONSOLE REMOVAL/INSTALLATION . 09–17–5
Boot Panel Removal Note . . . . . . . . . . 09–17–6
Console Cover Removal Note . . . . . . . 09–17–6
CONSOLE DISASSEMBLY/ASSEMBLY 09–17–6
GLOVE COMPARTMENT
REMOVAL/INSTALLATION . . . . . . . . . 09–17–7
LOWER PANEL
REMOVAL/INSTALLATION . . . . . . . . . 09–17–7
Driver’s side . . . . . . . . . . . . . . . . . . . . . 09–17–7
Passenger’s side . . . . . . . . . . . . . . . . . 09–17–7
METER HOOD
REMOVAL/INSTALLATION . . . . . . . . . 09–17–8
SIDE PANEL
REMOVAL/INSTALLATION . . . . . . . . . 09–17–8
SIDE WALL REMOVAL/INSTALLATION 09–17–8
FRONT DOOR TRIM
REMOVAL/INSTALLATION . . . . . . . . . 09–17–9
REAR DOOR TRIM
REMOVAL/INSTALLATION . . . . . . . . . 09–17–9
A-PILLAR TRIM
REMOVAL/INSTALLATION . . . . . . . . . 09–17–10
B-PILLAR LOWER TRIM REMOVAL . . . 09–17–10
B-PILLAR LOWER TRIM
INSTALLATION . . . . . . . . . . . . . . . . . . . 09–17–11
B-PILLAR UPPER TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–11
C-PILLAR TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–11
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–11
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–12
REAR PACKAGE TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–12
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–12
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–12
FRONT SCUFF PLATE
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–13
REAR SCUFF PLATE
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–13
FRONT SIDE TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–13
TIRE HOUSE TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–13
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–13
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–14
TRUNK END TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–14
TRUNK SIDE TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–15
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–15
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–17–15
TRUNK SIDE UPPER TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–15
LIFTGATE TRIM
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–16
HEADLINER
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–16
FLOOR COVERING
REMOVAL/INSTALLATION . . . . . . . . . . 09–17–17
End of Toc
DASHBOARD REMOVAL/INSTALLATION
A3U091755100W01
1. Remove the passenger-side air bag module if equipped. (See 08–10–6 PASSENGER-SIDE AIR BAG
MODULE REMOVAL/INSTALLATION.)
2. Remove the combination switch. (See 09–18–12 COMBINATION SWITCH REMOVAL/INSTALLATION.)
3. Remove the installation bolts then shift the assembled steering shaft in the dashboard. (See 06–12–6
STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
4. Remove the instrument cluster. (See 09–22–3 INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
5. Remove the console. (See 09–17–5 CONSOLE REMOVAL/INSTALLATION.)
6. Remove the glove compartment.
7. Remove the lower panel.
8. Remove the hood release cable installation nut.
9. Remove the side wall.
10. Remove the A-pillar trim. (See 09–17–10 A-PILLAR TRIM REMOVAL/INSTALLATION.)
11. Remove the side panel.
1712-1U-01G(09-17).fm 1 ページ 2001年6月29日 金曜日 午前10時35分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст