Mazda Protege 5. Manual — part 331
EXTERIOR TRIM
09–16–3
09–16
REAR FINISHER REMOVAL/INSTALLATION
A3U091650810W01
1. Remove the nuts.
2. Pull the rear finisher toward you, then disengage
clip A from the body.
3. Install in the reverse order of removal.
End Of Sie
LIFTGATE GARNISH REMOVAL/INSTALLATION
A3U091650810W02
1. Remove the liftgate key cylinder. (See 09–11–7 LIFTGATE REMOVAL/INSTALLATION.)
2. Remove the bolts.
3. Disengage clip A using pliers.
4. Pull the liftgate garnish downward, then remove it.
5. Install in the reverse order of removal.
End Of Sie
SIDE PROTECTOR REMOVAL
A3U091650680W01
1. Pry the side protector end 20—30 mm {0.8—
1.1 in} using a flathead screwdriver or a razor.
Warning
••••
Using a razor with bare hands can cause
injury. Always wear gloves when using a
razor.
2. Pull the side protector toward you, then remove it.
Note
•
The side protector is installed with
double-sided adhesive tape. If the side
protector is difficult to remove, soften the
double-sided adhesive tape using a hot air blower.
End Of Sie
X3U916WA5
A3U0916W004
A3U0916W005
Y3U916WA1
1712-1U-01G(09-16).fm 3 ページ 2001年6月29日 金曜日 午前10時34分
EXTERIOR TRIM
09–16–4
SIDE PROTECTOR INSTALLATION
A3U091650680W02
1. Remove the adhesive remaining on the side protector (if it will be reused) and the body using a razor.
2. Remove any grease or dirt from the adhesion surface of the side protector (if it will be reused) and the body.
3. Attach double-sided adhesive tape to the side
protector as shown (if it will be reused).
Clearance
a: 25.0 mm {0.98 in}
b: 7.0 mm {0.28 in}
c: 1.0—3.0 mm {0.04—0.11 in}
d: 9.0 mm {0.35 in}
4. Peel off the backing from the double-sided
adhesive tape and attach the side protector onto
the body as shown.
Clearance
a: 0.66—3.66 mm {0.03—0.14 in}
b: 7.74 mm {0.30 in}
c: 4.0—7.0 mm {0.16—0.27 in}
d: 0.5—3.5 mm {0.02—0.13 in}
e: 3.0—6.0 mm {0.12—0.23 in}
End Of Sie
SIDE STEP MOLDING REMOVAL/INSTALLATION
A3U091651100W01
1. Remove the fasteners and clips B.
2. Disengage clips A from the vehicle front to
remove the side step molding.
3. Install in the reverse order of removal.
End Of Sie
ROOF RACK REMOVAL/INSTALLATION
A3U091651720W01
1. Remove the headliner.
2. Remove the nuts.
3. Pull the roof rack upward, then remove the roof
rack from the roof.
4. Install in the reverse order of removal.
End Of Sie
A3U0916W002
A3U0916W003
A3U0916W008
Z4F7728W001
1712-1U-01G(09-16).fm 4 ページ 2001年6月29日 金曜日 午前10時34分
EXTERIOR TRIM
09–16–5
09–16
ROOF RACK DISASSEMBLY/ASSEMBLY
A3U091651720W02
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
End Of Sie
ROOF CARRIER REMOVAL/INSTALLATION
A3U091651720W03
Caution
••••
When installing the front carrier bar to the vehicle, use two or more people to do the work and do
not scratch the vehicle body.
Front
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
1
Front cap
2
Rear cap
3
Screw
4
Front stay
5
Rear stay
Z4F7728W002
1
Screw
2
Cover A
3
Cover B
4
Bolt
5
Front carrier bar
(See 09–16–6 Front Carrier Bar Installation Note.)
A3U0916W011
1712-1U-01G(09-16).fm 5 ページ 2001年6月29日 金曜日 午前10時34分
EXTERIOR TRIM
09–16–6
Front Carrier Bar Installation Note
1. Loosen the bolt under the front carrier bar, and
adjust the front carrier bar position.
Rear
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
Rear Carrier Bar Removal Note
1. Loosen the bolt, slide the rear carrier bar and
stay, and remove them from the rail.
A3U0916W014
1
Front cover
2
Screw A
3
Cover A
4
Bolt
5
Rear carrier bar
(See 09–16–6 Rear Carrier Bar Removal Note.)
(See 09–16–7 Rear Carrier Bar Installation Note.)
6
Spacer
7
Stay
8
Screw B
9
Cover B
10
Rear cover
A3U0916W013
A3U0916W010
1712-1U-01G(09-16).fm 6 ページ 2001年6月29日 金曜日 午前10時34分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст