Mazda Protege 5. Manual — part 330
SUNROOF
09–15–17
09–15
5HB
1. Remove the headliner. (See 09–17–16 HEADLINER REMOVAL/INSTALLATION.)
2. Connect the sunroof switch connector.
3. Connect the negative battery cable.
4. Measure the voltage at the sunroof relay terminals as indicated below.
5. Disconnect the sunroof relay connector before inspecting for continuity at terminal H.
•
If not as specified, inspect the parts listed under “Action” and the related wiring harnesses.
•
If the parts and wiring harnesses are okay but the system still does not work properly, replace the sunroof
relay.
Terminal voltage list (Reference)
End Of Sie
Terminal
Signal
Connected to
Test condition
Voltage (V)/
Continuity
Action
1A
Slide close/
tilt up
Sunroof motor
Sunroof is opening/tilting
down.
0
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect sunroof motor
(See 09–15–12 SUNROOF
MOTOR INSPECTION)
•
Inspect related harness
Sunroof is closing/tilting up.
B+
Other
0
1B
Slide close/
tilt up
Sunroof motor
(Limit switch)
Sunroof is closing/tilting up.
0
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect sunroof motor (Limit
switch)
(See 09–15–12 SUNROOF
MOTOR INSPECTION)
•
Inspect related harness
Other
B+
1C
IG2
Sunroof switch
IG SW is at ON position.
B+
•
Inspect A/C 15 A fuse
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
0
1D
-
Not used
-
-
-
1F
IG2
Sunroof switch
IG SW is at ON position.
B+
•
Inspect A/C 15 A fuse
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect related harness
Other
0
1H
Sunroof relay
ground
GND
Under any condition: inspect
for continuity to ground.
Yes
•
Inspect related harness
1I
Slide open/
tilt down
Sunroof motor
Sunroof is opening/tilting
down.
B+
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect sunroof motor
(See 09–15–12 SUNROOF
MOTOR INSPECTION)
•
Inspect related harness
Sunroof is closing/tilting up.
0
Other
0
1J
Slide open/
tilt down
Sunroof motor
(Limit switch)
Sunroof is opening/tilting
down.
0
•
Inspect sunroof switch
(See 09–15–18 SUNROOF
SWITCH INSPECTION)
•
Inspect sunroof motor (Limit
switch)
(See 09–15–12 SUNROOF
MOTOR INSPECTION)
•
Inspect related harness
Other
B+
A3U0915W021
1712-1U-01G(09-15).fm 17 ページ 2001年6月29日 金曜日 午前10時33分
SUNROOF
09–15–18
SUNROOF SWITCH REMOVAL/INSTALLATION
A3U091566560W01
Note
•
The sunroof switch is together with the spot light.
1. Disconnect the negative battery cable.
2. Remove the spot light from the headliner. (See 09–18–21 MAP LIGHT REMOVAL/INSTALLATION.)
3. Install in the reverse order of removal.
End Of Sie
SUNROOF SWITCH INSPECTION
A3U091566560W02
1. Remove the sunroof switch. (See 09–18–21 MAP LIGHT REMOVAL/INSTALLATION.)
2. Inspect for continuity between the sunroof switch
terminals using an ohmmeter.
•
If not as specified, replace the sunroof switch.
End Of Sie
Z3U0915W001
X3U915WAU
1712-1U-01G(09-15).fm 18 ページ 2001年6月29日 金曜日 午前10時33分
EXTERIOR TRIM
09–16–1
09–16
09–16
EXTERIOR TRIM
COWL GRILLE
REMOVAL/INSTALLATION . . . . . . . . . 09–16–1
EXTRACTOR CHAMBER
REMOVAL/INSTALLATION . . . . . . . . . 09–16–1
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–16–1
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–16–2
FRONT FLAP
REMOVAL/INSTALLATION . . . . . . . . . 09–16–2
REAR FLAP
REMOVAL/INSTALLATION . . . . . . . . . 09–16–2
RADIATOR
GRILLE REMOVAL/INSTALLATION . . 09–16–2
REAR FINISHER
REMOVAL/INSTALLATION . . . . . . . . . 09–16–3
LIFTGATE GARNISH
REMOVAL/INSTALLATION . . . . . . . . . 09–16–3
SIDE PROTECTOR REMOVAL . . . . . . . 09–16–3
SIDE PROTECTOR INSTALLATION . . . 09–16–4
SIDE PROTECTOR INSTALLATION . . . 09–16–4
SIDE STEP MOLDING
REMOVAL/INSTALLATION . . . . . . . . . 09–16–4
ROOF RACK
REMOVAL/INSTALLATION . . . . . . . . . 09–16–4
ROOF RACK
DISASSEMBLY/ASSEMBLY . . . . . . . . . 09–16–5
ROOF CARRIER
REMOVAL/INSTALLATION . . . . . . . . . . 09–16–5
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–16–5
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–16–6
FRONT BELTLINE MOLDING
REMOVAL/INSTALLATION . . . . . . . . . . 09–16–7
REAR BELTLINE MOLDING
REMOVAL/INSTALLATION . . . . . . . . . . 09–16–7
REAR WINDOW GLASS
MOLDING REMOVAL . . . . . . . . . . . . . . 09–16–7
EAR WINDOW GLASS
MOLDING INSTALLATION . . . . . . . . . . 09–16–7
WINDSHIELD MOLDING REMOVAL. . . . 09–16–8
WINDSHIELD MOLDING
INSTALLATION . . . . . . . . . . . . . . . . . . . 09–16–8
ROOF MOLDING
REMOVAL/INSTALLATION . . . . . . . . . . 09–16–8
REAR SPOILER
REMOVAL/INSTALLATION . . . . . . . . . . 09–16–8
4SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–16–8
5HB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09–16–9
End of Toc
COWL GRILLE REMOVAL/INSTALLATION
A3U091650790W01
1. Remove the windshield wiper arm and blade. (See 09–19–5 WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION.)
2. Remove the weatherstrip.
3. Disengage the clips of the cowl grille using a
fastener remover, then remove the cowl grille.
4. Install in the reverse order of removal.
End Of Sie
EXTRACTOR CHAMBER REMOVAL/INSTALLATION
A3U091651920W01
4SD
1. Remove the rear bumper.
2. Remove the passenger-side trunk side trim.
3. Remove the screw.
4. Squeeze the clips with your fingers and remove
the extractor chamber from the vehicle side.
5. Install in the reverse order of removal.
X3U916WA0
X3U916WA1
1712-1U-01G(09-16).fm 1 ページ 2001年6月29日 金曜日 午前10時34分
EXTERIOR TRIM
09–16–2
5HB
1. Remove the rear bumper.
2. Squeeze the clips with your fingers and remove
the extractor chamber from the vehicle side.
3. Install in the reverse order of removal.
End Of Sie
FRONT FLAP REMOVAL/INSTALLATION
A3U091651840W01
1. Remove the bolts and fasteners.
2. Remove the front flap.
3. Install in the reverse order of removal.
End Of Sie
REAR FLAP REMOVAL/INSTALLATION
A3U091651940W01
1. Remove the bolts.
2. Remove the rear flap.
3. Install in the reverse order of removal.
End Of Sie
RADIATOR GRILLE REMOVAL/INSTALLATION
A3U091650710W01
1. Remove the front bumper. (See 09–10–5 FRONT BUMPER REMOVAL/INSTALLATION.)
2. Pull the radiator grille forward to disengage clips
A and tabs B from the front bumper.
3. Install in the reverse order of removal.
End Of Sie
A3U0916W001
X3U916WA2
X3U916WA3
Y3E7728W001
1712-1U-01G(09-16).fm 2 ページ 2001年6月29日 金曜日 午前10時34分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст