Mazda Protege 5. Manual — part 260
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05–18–2
SELECTOR LEVER INSPECTION
A3U051846102W01
1. Turn the ignition switch to the ON position (engine off).
2. With the brake pedal depressed, verify that a “click” sound is heard at each range when shifted in the pattern
shown.
3. Verify that the selector lever can only be shifted as shown.
4. Verify that a “click” sound is heard at each position when shifted from P position to 1 range.
5. Verify that the positions of the selector lever and the
indicator are aligned.
6. Verify that the position of the selector lever and the
selector illumination light correspond.
•
If not as specified, adjust the TR switch. (See 05–
17–23 TRANSAXLE RANGE (TR) SWITCH
ADJUSTMENT.)
7. Verify that the vehicle operates in each selected
range.
End Of Sie
SELECTOR LEVER ADJUSTMENT
A3U051846102W02
1. Remove the center console.
2. Shift the selector lever to the P position.
3. Unlock the lock piece of the selector cable (selector
lever side) in the order shown in the figure.
4. Verify that the manual shaft is at the P position.
5. Lock the lock piece of the selector cable (selector lever
side) in the order shown in the figure.
6. Install the center console.
7. Shift the selector lever from P position to 1 range, and
make sure that there are no other components in that
area to interfere with the lever.
End Of Sie
X3U518WA1
X3U518WA2
X3U518WA3
1712-1U-01G(05-18).fm 2 ページ 2001年6月29日 金曜日 午前10時14分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05–18–3
05–18
SELECTOR LEVER REMOVAL/INSTALLATION
A3U051846102W03
1. Disconnect the negative battery cable.
2. Remove the center console.
3. Disconnect the brake switch connector.
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
.
X3U518WA4
1
Connector
2
Selector cable
(See 05–18–4 Selector Cable Removal Note.)
(See 05–18–6 Selector Cable Installation Note.)
3
Clip
4
Clip
5
Interlock cable and lock unit
(See 05–18–4 Interlock Cable and Lock Unit
Installation Note.)
6
Nut
7
Selector lever
8
Seal rubber
1712-1U-01G(05-18).fm 3 ページ 2001年6月29日 金曜日 午前10時14分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05–18–4
Selector Cable Removal Note
Note
•
Remove the clip shown in the figure before
removing the selector cable from manual
shaft lever.
Interlock Cable and Lock Unit Installation Note
1. Verify that the ignition switch is at ACC position, and shift the selector lever to P position.
2. Press the lock unit onto the brake pedal stopper bracket.
3. From this position, slide the lock unit to fix the
lock unit hook into the bracket hole securely as
shown in the figure.
4. Install the interlock cable to the key cylinder.
5. Slide the outer casing to the key cylinder. Verify
that the outer casing hook is secured in the
cylinder hole.
6. Insert the clip over the convex part of the outer
casing.
Caution
••••
Allowing the interlock cable to become
bent or twisted during installation can
affect the lock unit operation.
7. Install the interlock cable end onto the cam pin on
the selector lever.
X3U518WAP
X3U518WA5
X3U518WA6
X3U518WA7
1712-1U-01G(05-18).fm 4 ページ 2001年6月29日 金曜日 午前10時14分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05–18–5
05–18
8. Fit the interlock cable in the U-groove in the
selector lever base plate, and install the clip.
Note
•
Steps 9—12 are for the interlock cable
replacement only.
Caution
••••
Applying load to the interlock cable while
pressing the lock piece in can affect the
lock unit operation.
9. Press the interlock cable lock piece in until it is
locked.
10. Screw the brake switch into the slider pin of the
lock unit as far as possible.
11. From this position, turn the brake switch
counterclockwise about 90 degrees, then tighten
the lock nut.
Tightening torque
13.8—17.6 N·m {140—180 kgf·cm, 122—156
in·lbf}
12. Remove the lock unit pin in the order shown in the
figure.
X3U518WA8
X3U518WA9
X3U518WAA
X3U518WAB
X3U518WAC
1712-1U-01G(05-18).fm 5 ページ 2001年6月29日 金曜日 午前10時14分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст