Mazda Protege 5. Manual — part 262
TECHNICAL DATA
05–50–1
05–50
05–50
TECHNICAL DATA
TRANSMISSION/TRANSAXLE
TECHNICAL DATA . . . . . . . . . . . . . . . . 05–50–1
End of Toc
TRANSMISSION/TRANSAXLE TECHNICAL DATA
A3U055001024W01
Item
Engine
ZM
FS
CLUTCH
Clutch pedal
Full stroke
(mm {in})
130—140 {5.12—5.51}
Height (from set plate)
(mm {in})
210—215 {8.27—8.46}
Free play
(mm {in})
0.7—3.5 {0.03—0.13}
Clutch cover
Diaphragm
spring fingers
Depth
(mm {in})
0.5 {0.020}
Misalignment
(mm {in})
0.6 {0.024}
Maximum clearance of
flatness of the pressure plate
(mm {in})
0.5 {0.020}
Clutch disc
Minimum thickness
(mm {in})
0.3 {0.012}
Run out limit
(mm {in})
0.7 {0.028}
Flywheel
Run out limit
(mm {in})
0.2 {0.008}
MANUAL TRANSAXLE
Transaxle type
F25M-R
G15M-R
Transaxle oil
Grade
API Service GL-4 or GL-5
Viscosity
All season
SAE 75W—90
Above 10
°
C {50
°
F}
SAE 80W—90
Capacity (Approx. quantity)
(L {US qt, Imp qt})
2.68 {2.83, 2.36}
AUTOMATIC TRANSAXLE
Transaxle type
FN4A-EL
Line pressure
D, 2, 1 range
Idle
330—470 {3.4—4.7, 49—66}
Stall
1,200—1,360 {12.3—13.8,
175—196}
1,160—1,320 {11.9—13.4,
170—190}
(kPa {kgf/cm
2
, psi}) R position
Idle
490—710 {5.0—7.2, 72—100}
Stall
1,470—1,690 {15.0—17.2, 214—244}
Engine stall
speed
(rpm)
D, 2, 1 range
2,300—2,600
2,200—2,500
R position
2,300—2,600
2,200—2,500
Time lag
(sec)
N
→
D
0.4—0.7
N
→
R
0.4—0.7
Transaxle fluid
temperature (TFT)
sensor
–20
°
C {–4
°
F}
236—324
0
°
C {32
°
F}
84.3—110
20
°
C {68
°
F}
33.5—42.0
40
°
C {104
°
F}
14.7—17.9
60
°
C {140
°
F}
7.08—8.17
80
°
C {176
°
F}
3.61—4.15
(kilohm) 100
°
C {212
°
F}
1.96—2.24
120
°
C {248
°
F}
1.13—1.28
130
°
C {266
°
F}
0.87—0.98
Input/turbine
speed sensor
(ohm)
ATF temperature: –40—160
°
C {–40—
320
°
F}
250—600
Solenoid valve
(ohm)
Shift solenoid A
1.0—4.2
Shift solenoid B
1.0—4.2
Shift solenoid C
1.0—4.2
Shift solenoid D
10.9—26.2
Shift solenoid E
10.9—26.2
Pressure control solenoid
2.4—7.3
1712-1U-01G(05-50).fm 1 ページ 2001年6月29日 金曜日 午前10時15分
TECHNICAL DATA
05–50–2
End Of Sie
Automatic transaxle fluid
(ATF)
Type
ATF M-V or equivalent (e.g. Dexron
®
III)
Capacity (Approx. quantity)
(L {US qt, Imp qt})
7.2 {7.6, 6.3}
Item
Engine
ZM
FS
1712-1U-01G(05-50).fm 2 ページ 2001年6月29日 金曜日 午前10時15分
SERVICE TOOLS
05–60–1
05–60
05–60
SERVICE TOOLS
TRANSMISSION/TRANSAXLE SST. . . . 05–60–1
End of Toc
TRANSMISSION/TRANSAXLE SST
A3U056001024W01
End Of Sie
49 0259 770B
Flare nut
wrench
49 SE01 310A
Clutch disc
centering tool
49 1285 071
Bearing puller
49 E011 1A0
Ring gear brake
set
49 F028 202
Bush installer
49 B001 797
Handle (Part of
49 B001 795)
49 B001 795
Oil seal installer
49 E017 5A0
Engine support
49 0378 400C
Oil pressure
gauge set
49 B019 901B
Oil pressure
gauge
49 H019 002
Adapter
49 G030 455
Diff. side gear
holder
49 G030 795
Oil seal installer
418FS475
WDS
—
1712-1U-01G(05-60).fm 1 ページ 2001年6月29日 金曜日 午前10時15分
06–10–1
06
STEERING
SECTION
06–10
Toc of SCT
GENERAL PROCEDURES . . . . 06-10
ENGINE SPEED SENSING
POWER STEERING . . . . . . . . 06-12
TECHNICAL DATA . . . . . . . . . 06-50
SERVICE TOOLS. . . . . . . . . . . 06-60
Toc of SCT
06–10
GENERAL PROCEDURES
PRECAUTION (STEERING). . . . . . . . . . . 06–10–1
Wheels and Tires
Removal/Installation . . . . . . . . . . . . . . 06–10–1
Power Steering Components
Removal/Installation . . . . . . . . . . . . . . 06–10–1
Connectors
Disconnection/Connection . . . . . . . . . 06–10–1
End of Toc
PRECAUTION (STEERING)
A3U061001034W01
Wheels and Tires Removal/Installation
1. The removal and installation procedures for the wheels and tires are not mentioned in this section. When a
wheel is removed, retighten it to 89—117 N·m {9.0—12.0 kgf·m, 65.1—86.7 ft·lbf}.
Power Steering Components Removal/Installation
1. If any power steering fluid line has been disconnected anytime during the procedure, add ATF M-
III
or
equivalent (e.g. Dexron
®
III
), bleed the fluid lines, and inspect for leakage after the procedure has been
completed.
Connectors Disconnection/Connection
1. Disconnect the negative battery cable before doing any work that requires handling of connectors. Reconnect
the negative battery cable only after the work is completed.
End Of Sie
1712-1U-01G(06-10).fm 1 ページ 2001年6月29日 金曜日 午前10時16分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст