Loader Bobcat 773. Manual — part 100
BOBCAT INTERLOCK CONTROL SYSTEM (BICS
™
)
(S/N 509648899 & Below) (S/N 509617299 &
Below)(Cont’d)
Maintenance
Clean any debris, dirt or objects from under or behind the
operator seat [A] & [B]. The rear of the seat must move
up and down.
Inspect both Seat Rail Covers [B] for wear or damage.
Replace if necessary.
Clearance is necessary under the seat spring (Item 1) [B]
and the seat, to allow the seat to move up and down freely.
With adequate clearance, the seat sensor will be allowed
to function properly.
Inspect seat bar pivot area for tightness of linkage bolts.
Replace parts that are damaged. Use only genuine
Melroe replacement parts.
The Bobcat Interlock Control System (BICS)
must deactivate the lift, tilt and traction drive
functions. If it does not, contact your dealer for
service. DO NOT modify the system.
W–2151–0394
AVOID INJURY OR DEATH
Revised June 01
A
P–03763
Clean area behind
and under seat.
–8–6–
773 BICS Loader
Service Manual
B
MC–02043
Operator
Seat
Seat
Spring
1
Seat
Sensor
Seat Rail
Cover
Seat
Operator in Seat
No Operator in Seat
Lift and tilt functions
will not operate.
Seat Bar
Seat Bar Down
Seat Bar Up
Lift, tilt and traction
2
Seat bar sensor circuit shorted to
functions will not
battery voltage*.
operate.
3
Seat bar sensor circuit shorted to
ground.
Valve
Control Valve Can Control Valve
Lift and tilt functions
1
Valve output circuit is open.
Be Used
Cannot Be Used
will not operate.
2
Valve output circuit shorted to battery
voltage*.
3
Valve output circuit shorted to ground.
3
Valve output circuit is not grounded.
Traction
Loader can be
Loader cannot be
Loader cannot be
1
Traction lock hold coil circuit is open.
moved forward &
moved forward and
moved forward and
2
Traction lock hold coil circuit shorted
backward.
backward.
backward.
to battery voltage*.
3
Traction lock hold coil circuit shorted
to ground.
4
Traction lock pull coil circuit is open.
5
Traction lock pull coil circuit is shorted
to battery voltage*.
6
Traction lock pull coil circuit is shorted
to ground.
Power
BICS Controller
BICS Controller is
Lift, tilt and traction
is operating
not operating
functions will not
correctly.
correctly.
operate.
2
Seat sensor circuit shorted to battery
voltage*.
3
Seat sensor circuit shorted to ground
Flashing Indicator Means System Problem
(See Your Bobcat Dealer for Service)
BOBCAT INTERLOCK CONTROL SYSTEM (BICS
™
) (S/N 509648899 & Below) (S/N 509617299 & Below)(Cont’d)
Troubleshooting Chart
The following list shows the effects which can happen to the loader, and the probable causes when the BICS Controller
lights are off or flashing. Have the service procedure performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL.
Effect on Operation
of Loader
Indicator
When Light Is
Number of
Light
Light ON
Light OFF
OFF
Flashes
Cause
NOTES:
(1) If the seat and/or seat bar sensor circuits are open, the corresponding lights will be OFF. If one of the lights
stay OFF, check the circuit for continuity.
(2) If all five lights flash repeatedly, the voltage supply is greater than 16 volts or less than 9 volts.
(3) Flashing patterns will repeat every 3.25 seconds.
(4) If seat indicator light does not go ON, check for debris, dirt or objects under or behind the seat.
NOTE: On some early models with BICS controller S/N 200,000 and Above only, If the Seat Bar is lowered before
the seat sensor is activated, a 10 second delay will occur before the valve and traction lights come on.
* Normal BICS operating voltage is less than the electrical system voltage. If voltage is more, the circuit is shorted
to system voltage.
Revised June 01
773 BICS Loader
–8–7–
Service Manual
BOBCAT INTERLOCK CONTROL SYSTEM (BICS
™
)
(Cont’d)
Troubleshooting Guide
The following troubleshooting guide is provided for
assistance in locating and correcting BICS system
problems. It is recommended that these procedures be
done by authorized Bobcat Service Personnel only.
BICS CONTROLLER
W–2004–1285
Check for correct function after adjustments,
repairs or service. Failure to make correct
repairs or adjustments can cause injury or
death.
1.
Check that ignition switch ON.
2.
Check BICS 10 amp. fuse.
3.
Check wiring and connections. Make sure the connector is securely connected
to the controller. Remove controller and pull on connector to check.
4.
Look at indicator light windows, if they are milky white in appearance it is most
likely caused by moisture in the controller. Allow to dry or replace the controller.
5.
Refer to BICS troubleshooting chart for your loader. (See Page 8–4 & 8–7.)
6.
Check wire connections to make sure connectors are locked into place.
7.
Check pins in connectors for pins pushed back or bent.
8.
Move the system wiring back & forth to try to find area that may be causing the
intermittent connection.
9.
Use sensor tester MEL1428 to isolate problem between sensor and controller
and wiring.
PROBLEM
SOLUTION #
Power indicator light does not come ON.
1, 2, 3, 6
All indicator lights flashing.
4
One of the indicator lights flashing.
5
Intermittent indicator lights.
6, 7, 8, 9
SOLUTION SUGGESTIONS
Revised June 01
–8–8–
773 BICS Loader
Service Manual
BOBCAT INTERLOCK CONTROL SYSTEM (BICS
™
)
(Cont’d)
Troubleshooting Guide (Cont’d)
The following troubleshooting guide is provided for
assistance in locating and correcting BICS system
problems. It is recommended that these procedures be
done by authorized Bobcat Service Personnel only.
TRACTION LOCK
W–2004–1285
Check for correct function after adjustments,
repairs or service. Failure to make correct
repairs or adjustments can cause injury or
death.
1.
Check that controller power indicator light is ON.
2.
Make sure brake pedal is not engaged.
3.
Maneuver loader to allow brake discs to move and remove pressure on the brake
wedge so it can retract.
4.
If all lights indicate the brake should be released, but it doesn’t, check the brake
25 amp. fuse.
5.
When checking fuse, also check other fuses. Check the fuse block for correct
orientation and location of fuses. (See Electrical System, Page 6–1.)
6.
To test the solenoid, the pull coil should be 0.4 to 0.5 ohms and the hold coil 10.5 to
11.0 ohms.
7.
Check brake solenoid and cover mounting hardware for the correct torque.
8.
Remove brake cover and check wedges for binding in the wedge guides.
9.
Check wire connections for loose connector body.
10.
Check for loose or bent pins in connectors.
11.
Check for loose spade connectors in fuse holder.
PROBLEM
SOLUTION #
Traction lock stays engaged.
1, 2, 3, 4, 5, 6, 7, 8
Intermittent activation of traction lock.
9, 10, 11
SOLUTION SUGGESTIONS
Revised Jan. 99
773 BICS Loader
–8–9–
Service Manual
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст