Acura CSX. Manual — part 363
*01
02
SNR9A00B44100056851KBAT02
18-38
Rear Suspension
Stabilizer Bar Replacement
B
C
D
A
Except Type S model:
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
Type S model:
10 x 1.25 mm
49 N·m
(5.0 kgf·m, 36 lbf·ft)
E
10 x 1.25 mm
39 N·m
(4.0 kgf·m,
29 lbf·ft)
A
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-11).
2. Remove the rear wheels.
3. Disconnect both stabilizer links from the stabilizer
bar (see page 18-37).
4. Remove the flange bolts (A) and the bushing
holders (B), then remove the bushings (C) and the
stabilizer bar (D).
NOTE: During installation, align the paint marks (E)
on the stabilizer bar with the sides of the bushings.
5. Replace the stabilizer bar bracket (A) if necessary.
6. Install the stabilizer bar in the reverse order of
removal, and note these items:
• Note the right and left direction of the stabilizer
bar.
• Refer to stabilizer link removal/installation to
connect the stabilizer bar to the links (see page
18-37).
• Before installing the wheel, clean the mating
surfaces of the brake disc and inside of the wheel.
7. Check the wheel alignment, and adjust it if
necessary (see page 18-5).
08/08/21 14:57:45 61SNR030_180_0038
01
SNR9A00B44100019102KBAT00
Exploded View
18-39
Damper Replacement
SELF LOCKING NUT
10 x 1.25 mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
DAMPER MOUNTING WASHER
DAMPER MOUNTING BUSHING
DAMPER UNIT
DUST COVER
Replace.
Check for bending and damage.
Check for weakness.
Check for oil leaks,
gas leaks, and smooth
operation.
Check for deterioration and damage.
08/08/21 14:57:45 61SNR030_180_0039
02
03
03
Removal
18-40
Rear Suspension
C
12 x 1.25 mm
A
B
D
A
10 x 1.25 mm
B
C
A
B
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-11).
2. Remove the rear wheel.
3. Position a floor jack at the connecting point of the
trailing arm (A) and the knuckle (B). Raise the floor
jack until the suspension begins to compress.
4. Remove the flange bolt (C) that connects the
trailing arm and the damper (D).
5. Remove the trunk side trim panel (see page 20-80).
6. Remove the self-locking nut (A) while holding the
damper shaft (B) with a hex wrench (C).
7. Compress the damper unit (A) by hand, and
remove it from the vehicle.
NOTE: Be careful not to damage the body.
8. Remove the damper mounting bushing (B).
Replace.
Replace.
08/08/21 14:57:46 61SNR030_180_0040
05
06
01
Inspection
Installation
18-41
A
B
A
Except Type S model:
12 x 1.25 mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
Type S model:
12 x 1.25 mm
69 N·m (7.0 kgf·m, 51 lbf·ft)
1. Push on the damper as shown.
2. Compress the damper assembly by hand, and
check for smooth operation through a full stroke,
both compression and extension. The damper
should extend smoothly and constantly when
compression is released. If it does not, the gas is
leaking and the damper should be replaced.
3. Check for oil leaks, abnormal noises, or binding
during these tests.
1. Install the damper mounting bushing (A) onto the
damper unit. Position the damper assembly (B)
between the body and trailing arm.
NOTE: Be careful not to damage the body.
2. Position a floor jack under the trailing arm to
support the suspension, then install the new
damper mounting bolt (A).
3. Loosely tighten the damper mounting bolt.
4. Raise the rear suspension with the jack until the
vehicle just lifts off the safety stands, then tighten
the damper mounting bolt to the specified torque
value.
Replace.
Replace.
08/08/21 14:58:17 61SNR030_180_0041
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст