Acura CSX. Manual — part 364
04
05
01
SNR9A00B44100056301KBAT00
Exploded View
18-42
18-42
Rear Suspension
Spring Replacement
A
B
C
10 x 1.25 mm
B
C
A
10 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
SPRING MOUNTING
RUBBER
SPRING
LOWER SPRING SEAT
5. Install the damper mounting bushing (A), the
damper mounting washer (B), and the new self-
locking nut (C) on the damper shaft.
6. Tighten the self-locking nut (A) to the specified
torque value while holding the damper shaft (B)
with a hex wrench (C).
7. Install the trunk side trim panel (see page 20-80).
8. Clean the mating surfaces of the brake disc and the
inside of the wheel, then install the rear wheel.
9. Check the wheel alignment, and adjust it if
necessary (see page 18-5).
Replace.
Replace.
Check for weakness
and damage.
Check for damage.
Check for deterioration
and damage.
08/08/21 14:58:17 61SNR030_180_0042
04
05
01
SNR9A00B44100056301KBAT00
Exploded View
18-42
18-42
Rear Suspension
Spring Replacement
A
B
C
10 x 1.25 mm
B
C
A
10 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
SPRING MOUNTING
RUBBER
SPRING
LOWER SPRING SEAT
5. Install the damper mounting bushing (A), the
damper mounting washer (B), and the new self-
locking nut (C) on the damper shaft.
6. Tighten the self-locking nut (A) to the specified
torque value while holding the damper shaft (B)
with a hex wrench (C).
7. Install the trunk side trim panel (see page 20-80).
8. Clean the mating surfaces of the brake disc and the
inside of the wheel, then install the rear wheel.
9. Check the wheel alignment, and adjust it if
necessary (see page 18-5).
Replace.
Replace.
Check for weakness
and damage.
Check for damage.
Check for deterioration
and damage.
08/08/21 14:58:17 61SNR030_180_0042
02
03
05
04
Removal
18-43
A
B
6 x 1.0 mm
C
8 x 1.25 mm
A
C
12 x 1.25 mm
D
B
B
C
A
12 x 1.25 mm
A
12 x 1.25 mm
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-11).
2. Remove the rear wheel.
3. Remove the wheel speed sensor (A) from the
knuckle (B). Do not disconnect the wheel speed
sensor connector.
4. Remove the brake hose mounting bolt (C) from the
bracket.
5. Position a floor jack at the connecting point of the
trailing arm (A) and the knuckle (B). Raise the floor
jack until the suspension begins to compress.
6. Remove the flange bolt (C) that connects the
trailing arm and the damper (D).
7. Disconnect the stabilizer link from the trailing arm
(see page 18-37).
8. Remove the flange bolt (A) that connects the
knuckle (B) and the upper arm (C).
9. Remove the trailing arm front mounting bolts (A).
Replace.
Replace.
Replace.
08/08/21 14:58:18 61SNR030_180_0043
06
07
08
Installation
18-44
Rear Suspension
A
B
C
A
B
C
A
B
C
10. Lower the floor jack gradually.
11. Remove the spring mounting rubber (A), the spring
(B) and the lower spring seat (C).
NOTE: If the clip is installed inside the spring
mounting rubber, discard it.
1. Install the spring mounting rubber (A), the spring
(B) and the lower spring seat (C).
2. Align the bottom of the spring (A) and the lower
spring seat (B) with the trailing arm (C) as shown.
08/08/21 14:58:19 61SNR030_180_0044
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст