Acura CSX. Manual — part 421
07
08
*01
20-11
Fastener Locations
: Screw, 2
A
B
C
D
D
A
A
B
A
A
10. If necessary, remove the special screws, then
separate the door cylinder (A) and the outer handle
protector (B). If the retainer (C) is damaged, release
the hooks (D), and replace it.
NOTE: If removed, the special screws must be
replaced.
11. While pulling the outer handle (A), remove the
handle from the holes in the door panel. Take care
not to scratch the door.
12. Remove the rod fastener (A) from the outer handle
(B), then replace it with a new one.
13. Install the handle in the reverse order of removal,
and note these items:
• Make sure the cylinder cable and each rod is
connected securely.
• Make sure the door key cylinder/door locks
operate properly.
• Make sure the door handle works properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
• Check for water leaks (see step 9 on page 20-29).
Replace.
08/08/21 14:59:00 61SNR030_200_0013
01
02
SNR9A00J16126720801KBAT20
20-12
Doors
Front Door Latch Replacement
Fastener Location
: Bolt, 1
6 x 1.0 mm
8 N·m
(0.8 kgf·m, 6 lbf·ft)
A
B
Fastener Locations
: Screw, 3
D
: Screw, 1
E
A
B
C
D
E
F
G
D
D
6 x 1.0 mm
6 N·m
(0.6 kgf·m,
4 lbf·ft)
6 x 1.0 mm
6 N·m
(0.6 kgf·m,
4 lbf·ft)
NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel and inner handle (see page
20-7).
3. Remove the plastic cover, as needed (see step 4 on
page 20-9).
4. Detach the rod fastener (see step 5 on page 20-9).
5. Disconnect the outer handle rod from the outer
handle (see step 6 on page 20-10).
6. Disconnect the cylinder cable from the latch (see
step 7 on page 20-10).
7. Pull the glass run channel (A) away as needed, and
remove the bolt, then remove the center lower
channel (B) by pulling it downward.
8. Detach the latch cable (A) and the inner handle
cable (B) from the holder (C), then remove the
screws (D, E) securing the latch (F), then remove
the latch through the hole in the door. Take care not
to bend the outer handle rod (G), the latch cable, or
the inner handle cable.
08/08/21 14:59:01 61SNR030_200_0014
03
04
20-13
Fastener Location
: Screw, 1
A
B
A
A
B
B
C
9. Remove the screw, then remove the latch protector
(A) by releasing the hook (B).
10. Disconnect the latch cable (A) and the inner handle
cable (B) from the latch (C).
11. Install the latch in the reverse order of removal, and
note these items:
• Make sure the actuator connector is plugged in
properly and each rod is connected securely.
• Make sure the door locks and opens properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
• Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:01 61SNR030_200_0015
01
02
03
SNR9A00J54400020371KBAT10
20-14
Doors
Front Door Glass and Regulator Replacement
E
D
A
B
E
F
B
D
C
Fastener Locations
: Bolt, 2
A
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
C
D
E
E
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
Fastener Locations
: Bolt, 2
D
: Bolt, 2
E
(Black)
(Gold)
NOTE: Put on gloves to protect your hands.
1. Remove the door panel (see page 20-7).
2. Disconnect the power door lock actuator connector
(A) and remove the plug caps (B).
3. Pass the cables (C) and the harnesses (D) through
the slits (E) in the plastic cover (F), then remove the
plastic cover.
4. Carefully raise the glass (A) until you can see the
bolts, then remove them. Carefully pull the glass
out through the window slot. Take care not to drop
the glass inside the door.
5. Disconnect the connector (A), and detach the
harness clip (B) from the regulator (C).
6. Remove the bolts (D), and loosen the bolts (E), then
remove the regulator through the hole in the door.
08/08/21 14:59:02 61SNR030_200_0016
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст