Acura CSX. Manual — part 420
01
06
07
08
20-8
Doors
Fastener Locations
A
D
E
F
G
A
: Clip, 6
B
: Clip, 1
C
B
B
B
B
C
B
B
B
A
C
C
A
C
B
A
B
C
D
F
E
G
F
6. Remove the door panel (A) with as little bending as
possible to avoid creasing or breaking it.
–1 Start at the bottom edge of the door panel,
release the clips (B, C) that are just above the
marks (D) on the edge of the panel with a
commercially available trim pad remover.
–2 Detach the upper clips.
–3 Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (E) and the latch
cable (F) are connected to the inner handle (G).
Do not pull the door panel up too far, or these
cables will be damaged.
7. While holding the door panel (A) away from the
door remove the inner handle (B) from the door
panel by releasing the hooks (C).
8. Remove the door panel (A) while pulling the inner
handle (B) out through the hole in the door panel,
and disconnect the courtesy light subharness
connector (C).
9. If necessary, disconnect the inner handle cable (A)
and the latch cable (B) from the inner handle (C),
then remove the handle.
–1 Detach the inner handle cable fastener (D),
then disconnect the inner handle cable from
the cable fastener (E).
–2 Detach the latch cable fastener (F) with a flat-
tip screwdriver, then disconnect the latch cable
from the cable fastener (G).
NOTE: If the cable fasteners are damaged or
stress-whitened, replace them with new ones.
08/08/21 14:58:58 61SNR030_200_0010
02
01
02
SNR9A00J16126721301KBAT00
20-9
20-9
Front Door Outer Handle
Replacement
A
B
62 mm (2.44 in.)
A
B
C
B
A
10. Install the door panel in the reverse order of
removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Replace any damaged cable fasteners with new
ones.
• The latch cable (A) should be fixed to the cable
fastener (B) with the latch in lock position.
• Make sure the connectors are plugged in
properly, and the cables are connected securely.
• Make sure the window and power door lock
operate properly.
NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel and inner handle (see page
20-7).
3. Disconnect the power door lock actuator connector
(A).
4. Remove the plug caps (B), then remove the plastic
cover (C), as needed.
5. Detach the rod fastener (A).
08/08/21 14:58:59 61SNR030_200_0011
02
01
02
SNR9A00J16126721301KBAT00
20-9
20-9
Front Door Outer Handle
Replacement
A
B
62 mm (2.44 in.)
A
B
C
B
A
10. Install the door panel in the reverse order of
removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Replace any damaged cable fasteners with new
ones.
• The latch cable (A) should be fixed to the cable
fastener (B) with the latch in lock position.
• Make sure the connectors are plugged in
properly, and the cables are connected securely.
• Make sure the window and power door lock
operate properly.
NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel and inner handle (see page
20-7).
3. Disconnect the power door lock actuator connector
(A).
4. Remove the plug caps (B), then remove the plastic
cover (C), as needed.
5. Detach the rod fastener (A).
08/08/21 14:58:59 61SNR030_200_0011
01
04
05
06
20-10
Doors
A
B
C
A
B
C
D
E
E
B
A
A
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
Fastener Location
: Bolt, 1
A
B
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
Fastener Location
: Bolt, 1
6. Remove the maintenance cap (A). Disconnect the
outer handle rod (B) with a clip remover (C).
7. Driver’s side: Pull both side flanges (A) of the
retainer (B) outward, and pull the middle flange
portion (C) of the outer casing cover (D) out, then
disconnect the cylinder cable (E) from the latch.
8. Remove the bolt, then remove the spacer (A).
9. Remove the bolt securing the outer handle
protector (A), then remove the protector by
releasing the hook (B).
08/08/21 14:59:00 61SNR030_200_0012
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст