Acura CSX. Manual — part 319
*05
*06
*07
14-348
Transmission Housing
B
A
C
C
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
GRN
ORN
RED
BLU
YEL,
WHT, WHT
G
D
E
B
C
F
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
C
B
A
B
20. Install the input shaft (mainshaft) speed sensor (A)
and the output shaft (countershaft) speed sensor
(B) with new O-rings (C).
21. Install the shift solenoid wire harness (F) in the
transmission housing with a new O-ring (G).
22. Connect the connectors to the respective valves:
• BLU wire to shift solenoid valve A.
• ORN wire to shift solenoid valve B.
• GRN wire to shift solenoid valve C.
• YEL, WHT, and WHT wire to shift solenoid valve
D.
• RED wire to shift solenoid valve E.
23. Install the shift solenoid valve cover (A) with the
two dowel pins (B) and a new gasket (C).
Replace.
Replace.
Replace.
Replace.
08/08/21 14:52:33 61SNR030_140_0350
*01
SNR9AA1E10410424251KCAT00
Exploded View
14-349
Transmission End Cover
End Cover Installation
A/T CLUTCH PRESSURE
CONTROL SOLENOID
VALVES B and C
TRANSMISSION RANGE
SWITCH COVER
TRANSMISSION
RANGE SWITCH
6 x 1.0 mm
6 x 1.0 mm
28 N·m
(2.9 kgf·m, 21 lbf·ft)
6 x 1.0 mm
TRANSMISSION
END COVER
6 x 1.0 mm
12 Bolts
28 N·m
(2.9 kgf·m, 21 lbf·ft)
CONICAL SPRING
WASHERS
PARK GEAR
STOP SHAFT
PARK
LEVER STOP
LOCK WASHER
14 N·m
(1.4 kgf·m,
10 lbf·ft)
PARK PAWL
PARK PAWL
SPRING
PARK PAWL
SHAFT
PARK LEVER
SPRING
MAINSHAFT
IDLER GEAR
TRANSMISSION
END COVER GASKET
HARNESS CLAMP
BRACKETS
6 x 1.0 mm
ATF JOINT
PIPES
ATF JOINT PIPES
ATF PIPE
6 x 1.0 mm
A/T CLUTCH PRESSURE
CONTROL SOLENOID
VALVE A
Torque Specifications
6 x 1.0 mm: 12 N·m (1.2 kgf·m, 8.7 lbf·ft)
28 N·m
(2.9 kgf·m,
21 lbf·ft)
PARK
LEVER
Replace.
Replace.
Replace.
08/08/21 14:52:34 61SNR030_140_0351
*02
02
03
Special Tools Required
14-350
Transmission End Cover
07GAB-PF50101
B
C
A
D
J
K
G
F
E
A
B
D
6 x 1.0 mm
14 N·m
(1.4 kgf·m,
10 lbf·ft)
C
H
I
Mainshaft holder 07GAB-PF50101
1. Install the mainshaft holder onto the mainshaft.
2. Lubricate the following parts with ATF:
• Splines and threads of the mainshaft.
• Splines of the mainshaft idler gear.
• Old conical spring washer and old locknut.
3. Install the mainshaft idler gear (A), the old conical
spring washer (B), and the old locknut (C) on the
mainshaft (D), and tighten the locknut to 226 N·m
(23.0 kgf·m, 166 lbf·ft).
NOTE:
• Do not tap the idler gear to install.
• Use a torque wrench to tighten the locknut. Do
not use an impact wrench.
4. Install the park lever (A) and the park lever stop (B)
on the selector control shaft (C), then install the
lock bolt with a new lock washer (D). Do not bend
the lock tab of the lock washer until step 18.
5. Install the park pawl shaft (E), the park pawl spring
(F), the park pawl (G), and the stop shaft (H) on the
transmission housing.
6. Lubricate the following parts with ATF:
• Threads and splines of the countershaft.
• Old conical spring washer and old locknut.
• Areas where the park gear contacts the conical
spring washer.
7. Install the park gear (I), the old conical spring
washer (J), and the old locknut (K) on the
countershaft.
8. Lift the park pawl up, and engage it with the park
gear, then tighten the locknut to 226 N·m
(23.0 kgf·m, 166 lbf·ft).
NOTE:
• Do not tap the park gear to install.
• Use a torque wrench to tighten the locknut. Do
not use an impact wrench.
• Countershaft locknut has left-hand threads.
9. Remove the locknuts and the conical spring
washers from the mainshaft and the countershaft.
08/08/21 14:52:35 61SNR030_140_0352
−
−
*03
01
*04
02
14-351
A
B
D
C
A
B
6 x 1.0 mm
14 N·m
(1.4 kgf·m, 10 lbf·ft)
C
B
A
6 x 1.0 mm
14 N·m
(1.4 kgf·m,
10 lbf·ft)
A
D
E
B
C
F
10. Lubricate the threads of the shafts, new locknuts
and new conical spring washers with ATF.
11. Install new conical spring washers (A) with facing
stamped mark side up in the direction shown, and
install a new mainshaft locknut (B), a new
countershaft locknut (C), and a new secondary
shaft locknut (D).
12. Tighten the locknuts to 167 N·m (17.0 kgf·m,
123 lbf·ft).
NOTE:
• Be sure to install the conical spring washers in
the direction shown.
• Use a torque wrench to tighten the locknut. Do
not use an impact wrench.
• Countershaft and secondary shaft locknuts have
left-hand threads.
13. Remove the mainshaft holder from the mainshaft.
14. Stake the locknuts into the shafts to a depth (A) of
0.7
1.3 mm (0.03
0.05 in.) using a 3.5 mm punch
(B).
15. Install the control lever (A) on the selector control
shaft (B), and install the bolt with a new lock
washer (C), then bend the lock tab of the lock
washer against the bolt head.
16. Set the park lever in the P position, then check that
the park pawl (A) engages the park gear (B).
17. If the park pawl does not engage fully, check the
distance (C) between the pawl shaft (D) and the
park lever roller pin (E) (see page 14-292).
18. Tighten the lock bolt, and bend the lock tab of the
lock washer (F) against the bolt head.
Replace.
Replace.
Left-hand threads
Replace.
Left-hand threads
Replace.
Replace.
08/08/21 14:52:36 61SNR030_140_0353
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст