Acura CSX. Manual — part 318
*01
SNR9AA1E10410459801KCAT00
Exploded View
14-344
Transmission Housing
Shaft Assembly and Housing Installation
TRANSMISSION HOUSING
MOUNTING BOLTS
10 x 1.25 mm
44 N·m(4.5 kgf·m, 33 lbf·ft)
19 Bolts
REVERSE
SHIFT FORK
SECONDARY
SHAFT
SUBASSEMBLY
DIFFERENTIAL
ASSEMBLY
TRANSMISSION
HANGER
MAINSHAFT
SUBASSEMBLY
NEEDLE
BEARING
REVERSE
SELECTOR
6 x 1.0 mm
14 N·m
(1.4 kgf·m, 10 lbf·ft)
COUNTERSHAFT
REVERSE GEAR
COUNTERSHAFT
SUBASSEMBLY
ATF FEED PIPE
ATF LUBRICATION PIPE
SHIFT SOLENOID
VALVE COVER
SELECTOR
CONTROL
SHAFT
BAFFLE
PLATE
LOCK WASHER
TRANSMISSION
HOUSING
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED SENSOR
DETENT
SPRING
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
O-RING
SHIFT
SOLENOID
WIRE
HARNESS
O-RING
O-RING
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:52:30 61SNR030_140_0346
02
*02
14-345
A
B
C
D
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
A
C
E
F
D
NOTE: Refer to the Exploded View as needed during the
following procedure.
1. Install the differential assembly in the torque
converter housing.
2. Install the baffle plate on the servo body (see step
9 on page 14-343).
3. Assemble the mainshaft, the countershaft, and the
secondary shaft.
4. Join the mainshaft subassembly (A), the
countershaft subassembly (B), and the secondary
shaft subassembly (C) together. Then install them
in the torque converter housing. Do not bump the
countershaft on the baffle plate (D).
5. Make sure if the countershaft and the differential
are clear of the baffle plate.
6. If the detent arm was removed, install the detent
arm (A) with the arm collar (B) on the servo body
(C), and install a new lock washer (D) by aligning its
cutout (E) with the projection (F) of the servo body.
Install and tighten the bolt, then bend the lock tab
of the lock washer against the bolt head.
Replace.
08/08/21 14:52:31 61SNR030_140_0347
04
05
*03
14-346
Transmission Housing
A
B
C
B
A
D
C
6 x 1.0 mm
14 N·m
(1.4 kgf·m, 10 lbf·ft)
B
A
E
7. Install the selector control shaft (A) in the torque
converter housing aligning the manual valve lever
pin (B) on the selector control shaft with the guide
of the manual valve (C). Pull the manual valve
gently when aligning the manual valve with the
selector control shaft.
8. Hook the detent spring (A) to the detent arm (B).
9. Turn the shift fork shaft (A) so the large chamfered
hole (B) is facing the fork bolt hole (C) of the
reverse shift fork (D).
10. Install the reverse shift fork and the reverse
selector together on the shift fork shaft and the
countershaft. Secure the reverse shift fork to the
shift fork shaft with the lock bolt and a new lock
washer (E), then bend the lock tab of the lock
washer against the bolt head.
11. Install the needle bearing and the countershaft
reverse gear on the countershaft.
12. Install the reverse idler gear in the transmission
housing (see page 14-299), if it was removed.
13. Install the idler gear shaft (see page 14-324), if it
was removed.
Replace.
08/08/21 14:52:31 61SNR030_140_0348
*04
08
09
−
−
14-347
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
A
D
E
C
F
G
A
A
B
B: 0
7 mm (0
0.28 in.)
A
14. Install the three dowel pins (A) and a new gasket (B)
on the torque converter housing (C).
15. Align the spring pin (D) of the selector control shaft
(E) with the transmission housing groove (F) by
turning the control shaft. Do not squeeze the end of
the control shaft tips together when turning the
shaft. If the tips are squeezed together, it will cause
a faulty shift position signal or position due to the
play between the control shaft and the
transmission range switch.
16. Place the transmission housing (G) on the torque
converter housing. Do not install the input shaft
(mainshaft) speed sensor and the output shaft
(countershaft) speed sensor before installing the
transmission housing on the torque converter
housing.
17. Use snap ring pliers to expand the snap ring of the
secondary shaft bearing. Then push the
transmission housing down to start the secondary
shaft bearing through the snap ring. Then release
the pliers. While rotating the reverse idler gear with
a screwdriver, push down the housing until it
bottoms and snap ring snaps in place in the
secondary shaft bearing snap ring groove.
18. Check that the secondary shaft bearing snap ring
(A) is seated in the bearing and the housing groove,
and that the ring end gap (B) is correct.
19. Install the transmission housing mounting bolts
along with the transmission hanger and the
harness clamp brackets, and tighten the 19 bolts in
at least two steps in a crisscross pattern.
Replace.
08/08/21 14:52:32 61SNR030_140_0349
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст