Acura CSX. Manual — part 327
02
02
*02
Special Tools Required
Inboard Joint Side
16-12
Driveline/Axle
A
A
B
C
B
D
B
C
A
• Boot band tool, KD-3191 or equivalent commercially
available
• Boot band pliers, Kent-Moore J-35910 or equivalent,
commercially available
NOTE: Refer to the Exploded View, as needed, during
this procedure.
1. Wrap the splines with vinyl tape (A) to prevent
damaging the inboard boot.
2. Install the inboard boot onto the driveshaft, then
remove the vinyl tape. Be careful not to damage the
inboard boot.
3. Install the spider (A) onto the driveshaft by aligning
the marks (B) you made on the spider and the end
of the driveshaft.
4. Install a new circlip (C) into the driveshaft groove.
Always rotate the circlip in its groove to make sure
it is fully seated.
5. Fit the rollers (A) onto the spider (B) with their high
shoulders (C) facing outward, and note these items:
• Reinstall the rollers in their original positions on
the spider by aligning the marks (D) you made.
• Hold the driveshaft pointed up to prevent the
rollers from falling off.
Replace.
08/08/21 14:51:26 61SNR030_160_0012
05
03
04
−
−
−
−
Grease quantity
Inboard joint:
K20Z2 engine model:
112
132 g
(4.0
4.7 oz)
K20Z3 engine model:
180
200 g
(6.3
7.0 oz)
16-13
A
A
B
C
A
6. Pack the inboard joint with the joint grease
included in the new inboard boot set.
7. Fit the inboard joint onto the driveshaft and note
these items:
• Reinstall the inboard joint onto the driveshaft by
aligning the marks (A) you made on the inboard
joint and the rollers.
• Hold the driveshaft so the inboard joint is
pointing up to prevent it from falling off.
8. Fit the boot ends (A) onto the driveshaft (B) and the
inboard joint (C).
Use the grease included
in the inboard boot set.
08/08/21 14:51:26 61SNR030_160_0013
−
−
−
−
−
−
−
−
−
−
*03
*04
07
07
Left driveshaft
Right driveshaft
Model
Left/Right
Driveshaft
Specified Length (A)
16-14
Driveline/Axle
A
A
A
B
C
A
B
9. Adjust the length (A) of the driveshaft to the figure
as shown, then adjust the boots to halfway
between full compression and full extension. Bleed
excess air from the boots by inserting a flat-tipped
screwdriver between the boot and the joint.
K20Z2
engine
model
Left
505.5
510.0 mm
(19.88
20.08 in.)
Right
493.0
498.0 mm
(19.41
19.61 in.)
K20Z3
engine
model
Left
511.0
516.0 mm
(20.12
20.31 in.)
Right
486.8
491.8 mm
(19.17
19.36 in.)
10. Install new boot bands.
• For the double loop type, go to step 11.
• For the low profile type, go to step 20.
11. Fit the boot ends onto the driveshaft and the
inboard joint, then install a new double loop band
(A) onto the boot (B).
NOTE: Pass the end of the new double loop band
through the clip (C) twice in the direction of the
forward rotation of the driveshaft.
12. Pull up the slack in the band by hand.
13. Mark a position (A) on the band 10
14 mm
(0.4
0.6 in.) from the clip (B).
Replace.
08/08/21 14:51:27 61SNR030_160_0014
−
−
08
09
10
11
16-15
A
B
C
90 degrees
A
14. Thread the free end of the band through the nose
section of the commercially available boot band
tool KD-3191 or equivalent (A), and into the slot on
the winding mandrel (B).
15. Using a wrench on the winding mandrel of the boot
band tool, tighten the band until the marked spot
(C) on the band meets the edge of the clip.
16. Lift up the boot band tool to bend the free end of
the band 90 degrees to the clip. Center-punch the
clip, then fold over the remaining tail onto the clip.
17. Unwind the boot band tool, and cut off the excess
free end of the band to leave a 5
10 mm
(0.2
0.4 in.) tail protruding from the clip.
18. Bend the band end (A) by tapping it down using a
hammer.
NOTE:
• Make sure the band and the clip do not interfere
with anything on the vehicle and the band does
not move.
• Clean any grease remaining on the surrounding
surfaces.
19. Repeat steps 11 through 18 for the band on the
other end of the boot.
08/08/21 14:51:28 61SNR030_160_0015
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст